NCGGUI and QtDragon

When I changed:

[DISPLAY]
NGCGUI_SUBFILE_PATH = /home/cnc/linuxcnc/nc_files/ngcgui_lib/

[RS274NGC]
SUBROUTINE_PATH = /home/cnc/linuxcnc/nc_files/ngcgui_lib/:~/linuxcnc/nc_files/examples/ngcgui_lib/utilitysubs; \
~/linuxcnc/nc_files/examples/probe/basic_probe/macros:~/linuxcnc/nc_files/examples/remap-subroutines:\
~/linuxcnc/nc_files/examples/ngcgui_lib/remap_lib

The same error still pops up

I'll look at the code when I'm off work.

Thank you
I am attaching the ini file
 

yeah, it's a pain in the butt, but you have to be very careful with all the different paths.......
you'll get.

I see a semicolon in the SUBROUTINE_PATH, they should all be colons.

I suspect that anything after that is likely to be ignored.

Are you absolutely sure this is the right path?
/home/cnc/linuxcnc/nc_files/ngcgui_lib/
Can you show me what is in that folder?

wait... you have two [RS274NGC] sections. you can only have one.

Also use this:

SUBROUTINE_PATH = ~/linuxcnc/nc_files/ngcgui_lib/:~/linuxcnc/nc_files/ngcgui_lib/utilitysubs:~/linuxcnc/nc_files/probe/basic_probe/macros

In the file: /home/cnc/linuxcnc/nc_files/ngcgui_lib/
I have it:  

wait... you have two [RS274NGC] sections. you can only have one.

you're right, i've corrected it

SUBROUTINE_PATH = ~/linuxcnc/nc_files/ngcgui_lib/:~/linuxcnc/nc_files/ngcgui_lib/utilitysubs:~/linuxcnc/nc_files/probe/basic_probe/macros

i changed it but nothing changed. the bug still pops up.
 

I noticed that I also have two [HAL]but when I corrected it and got:

[HAL]
HALFILE = my-mill.hal
HALFILE = custom.hal
POSTGUI_HALFILE = qtdragon_hd_postgui.hal
POSTGUI_HALFILE = qtdragon_hd_debugging.hal
POSTGUI_HALCMD = loadusr qtvcp test_probe
POSTGUI_HALCMD = loadusr qtvcp test_led
POSTGUI_HALCMD = loadusr halmeter

I receive a error:

Debug file information:
Note: Using POSIX realtime[QTvcp.QTVCP.QT_ISTAT][[33mWARNING[0m]  Invalid message configuration (missing icon) in INI File [DISPLAY] sectioN (qt_istat.py:400)Could not open command file 'qtdragon_hd_postgui.hal'79267958Stopping realtime threadsUnloading hal componentsNote: Using POSIX realtime 

When I leave only:

[HAL]
HALFILE = my-mill.hal
HALFILE = custom.hallinux

starts but I get the following message: 

NGCGUI also started to load but still not working.I see the lines but the program itself does not start, and when I press stop, this error pops up 
 
 

You are missing the on_abort.ngc file.
linuxcnc.org/docs/2.9/html/gui/qtdragon.html#_abort_detection

The [HAL] section must reflect the actual files you want loaded. The documentation shows sample code, it's not meant to be copied verbatim.

The 'file not open' error I believe is caused by the option to reload the last file on startup.
Since (I assume) there was no loaded file in memory when qtdragon shuts down, it would cause this error.
You can turn off this setting in the settings page or eventually it should fix it's self.

Chris