I can continue if I choose "retry", the error occur four times when loading the 4 last buttons ("tool measure", "auto skew", "auto zero", "versaprobe help"). After this, I can use the module except if I pass the cursor over one of these four buttons where I instantly get the error message.
Here is what I've got from the terminal output :
Code:
[QTvcp.QTVCP.QT_ISTAT][WARNING] INI Parsing Error, No PROGRAM_PREFIX Entry in DISPLAY, Using: ~/linuxcnc/nc_files (qt_istat.py:515)
[QTvcp.QTVCP.QT_ISTAT][WARNING] INI Parsing Error, No MAX_SPINDLE_0_OVERRIDE Entry in DISPLAY, Using: 1 (qt_istat.py:515)
[QTvcp.QTVCP.QT_ISTAT][WARNING] INI Parsing Error, No MIN_SPINDLE_0_OVERRIDE Entry in DISPLAY, Using: 0.5 (qt_istat.py:515)
No section: 'VERSA_PROBE_OPTIONS'
Adding section VERSA_PROBE_OPTIONS
No option 'ps_probevel' in section: 'VERSA_PROBE_OPTIONS'
No option 'ps_z_clearance' in section: 'VERSA_PROBE_OPTIONS'
No option 'ps_probe_max' in section: 'VERSA_PROBE_OPTIONS'
No option 'ps_probe_latch' in section: 'VERSA_PROBE_OPTIONS'
No option 'ps_probe_diam' in section: 'VERSA_PROBE_OPTIONS'
No option 'ps_xy_clearance' in section: 'VERSA_PROBE_OPTIONS'
No option 'ps_side_edge_length' in section: 'VERSA_PROBE_OPTIONS'
No option 'ps_probe_height' in section: 'VERSA_PROBE_OPTIONS'
No option 'ps_block_height' in section: 'VERSA_PROBE_OPTIONS'
No option 'use_tool_measurement' in section: 'VERSA_PROBE_OPTIONS'
No option 'ps_offs_x' in section: 'VERSA_PROBE_OPTIONS'
No option 'ps_offs_y' in section: 'VERSA_PROBE_OPTIONS'
No option 'ps_offs_z' in section: 'VERSA_PROBE_OPTIONS'
No option 'ps_offs_angle' in section: 'VERSA_PROBE_OPTIONS'
No option 'ps_probe_rapid_vel' in section: 'VERSA_PROBE_OPTIONS'
QBackingStore::endPaint() called with active painter; did you forget to destroy it or call QPainter::end() on it?
QBackingStore::endPaint() called with active painter; did you forget to destroy it or call QPainter::end() on it?
QBackingStore::endPaint() called with active painter; did you forget to destroy it or call QPainter::end() on it?
QBackingStore::endPaint() called with active painter; did you forget to destroy it or call QPainter::end() on it?
QBackingStore::endPaint() called with active painter; did you forget to destroy it or call QPainter::end() on it?
QBackingStore::endPaint() called with active painter; did you forget to destroy it or call QPainter::end() on it?
QBackingStore::endPaint() called with active painter; did you forget to destroy it or call QPainter::end() on it?
QBackingStore::endPaint() called with active painter; did you forget to destroy it or call QPainter::end() on it?
QBackingStore::endPaint() called with active painter; did you forget to destroy it or call QPainter::end() on it?
QBackingStore::endPaint() called with active painter; did you forget to destroy it or call QPainter::end() on it?
QBackingStore::endPaint() called with active painter; did you forget to destroy it or call QPainter::end() on it?
QBackingStore::endPaint() called with active painter; did you forget to destroy it or call QPainter::end() on it?
