Profile for lumberjack_jeff

Offline

User Type: User
Rank: New Member

Register Date: 27 Aug 2009
Last login: 9 months 3 weeks ago
Time Zone: UTC +0:00
Local Time: 12:04

Posts: 15
Profile views: 4

Gender: Unknown
Birthdate: Unknown

lumberjack_jeff's recent posts (15 messages )

	Subject	Replies / Views	Last Post

	hal_gpio.so missing RPI5 Debian Trixie Category: General LinuxCNC Questions Topic started 9 months 3 weeks ago, by lumberjack_jeff Last Post 9 months 3 weeks ago by unknown	Replies:2 Views:640	Last Post by unknown 9 months 3 weeks ago
	Raspberry Pi 4 Tutorial - fatal error Category: Installing LinuxCNC Topic started 7 years 2 months ago, by BigJohnT Last Post 5 years 8 months ago by jaro_p 1 2 3 ... 16	Replies:153 Views:67.6k	Last Post by jaro_p 5 years 8 months ago
	Sharp 90* turn in gcode becomes a large sweeping turn Category: General LinuxCNC Questions Topic started 6 years 7 months ago, by BobsGotCnc Last Post 6 years 7 months ago by PCW 1 2 3	Replies:20 Views:4534	Last Post by PCW 6 years 7 months ago
	Sharp 90* turn in gcode becomes a large sweeping turn Category: General LinuxCNC Questions Topic started 6 years 7 months ago, by BobsGotCnc Last Post 6 years 7 months ago by PCW 1 2 3	Replies:20 Views:4534	Last Post by PCW 6 years 7 months ago
	Sharp 90* turn in gcode becomes a large sweeping turn Category: General LinuxCNC Questions Topic started 6 years 7 months ago, by BobsGotCnc Last Post 6 years 7 months ago by PCW 1 2 3	Replies:20 Views:4534	Last Post by PCW 6 years 7 months ago
	Sharp 90* turn in gcode becomes a large sweeping turn Category: General LinuxCNC Questions Topic started 6 years 7 months ago, by BobsGotCnc Last Post 6 years 7 months ago by PCW 1 2 3	Replies:20 Views:4534	Last Post by PCW 6 years 7 months ago
	Sharp 90* turn in gcode becomes a large sweeping turn Category: General LinuxCNC Questions Topic started 6 years 7 months ago, by BobsGotCnc Last Post 6 years 7 months ago by PCW 1 2 3	Replies:20 Views:4534	Last Post by PCW 6 years 7 months ago
	Sharp 90* turn in gcode becomes a large sweeping turn Category: General LinuxCNC Questions Topic started 6 years 7 months ago, by BobsGotCnc Last Post 6 years 7 months ago by PCW 1 2 3	Replies:20 Views:4534	Last Post by PCW 6 years 7 months ago
	how to downgrade from 2.8.0 to 2.7.x? Category: Installing LinuxCNC Topic started 9 years 1 month ago, by lumberjack_jeff Last Post 9 years 1 month ago by Todd Zuercher	Replies:1 Views:2441	Last Post by Todd Zuercher 9 years 1 month ago
	soft limits while unhomed Category: General LinuxCNC Questions Topic started 9 years 9 months ago, by lumberjack_jeff Last Post 9 years 9 months ago by lumberjack_jeff	Replies:8 Views:2739	Last Post by lumberjack_jeff 9 years 9 months ago

Time to create page: 0.339 seconds

Powered by Kunena Forum