-
Configuring LinuxCNC
-
PnCConf Wizard
-
parameter or pin 'hm2_7i76e.0.watchdog.timeout_ns' not found
parameter or pin 'hm2_7i76e.0.watchdog.timeout_ns' not found
Less
More
-
Posts: 42
-
Thank you received: 4
-
-
28 May 2020 19:10 #169241
by msageryd
I installed LCNC 2.8 which has 7i96 support in pncconf. Made a rough config and tried to start LCNC. Got a weird error about a missing pin. It seems like the board is found, though.
I'm totally new to LCNC, this was a rough start.
From the error report:
hm2: loading Mesa HostMot2 driver version 0.15
hm2_eth: loading Mesa AnyIO HostMot2 ethernet driver version 0.2
hm2_eth: 192.168.1.121: Hardware address: 00:60:1b:16:01:71
hm2_eth: discovered 7I96
hm2/hm2_7i96.0: Smart Serial Firmware Version 43
hm2/hm2_7i96.0: 51 I/O Pins used:
.
.
./HighZ.hal:10: parameter or pin 'hm2_7i76e.0.watchdog.timeout_ns' not found
From the HAL file:
setp [HMOT](CARD0).watchdog.timeout_ns 5000000
From the ini file:
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 17810
-
Thank you received: 5925
-
-
Less
More
-
Posts: 16940
-
Thank you received: 4345
-
-
28 May 2020 19:44 - 28 May 2020 19:44 #169246
by PCW
Did you select 7i96 in pncconf?
I just tested with the latest version of 2.8 and its OK
Did you try updating to the latest 2.8 version?
Last edit: 28 May 2020 19:44 by
PCW.
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 17810
-
Thank you received: 5925
-
-
28 May 2020 19:52 - 28 May 2020 19:52 #169248
by tommylight
From the error report:hm2: loading Mesa HostMot2 driver version 0.15
hm2_eth: loading Mesa AnyIO HostMot2 ethernet driver version 0.2
hm2_eth: 192.168.1.121: Hardware address: 00:60:1b:16:01:71
hm2_eth: discovered 7I96
hm2/hm2_7i96.0: Smart Serial Firmware Version 43
hm2/hm2_7i96.0: 51 I/O Pins used:
.
.
./HighZ.hal:10: parameter or pin 'hm2_7i76e.0.watchdog.timeout_ns' not found
Must be going blind....
The error says 7i76e, the rest is 7i96, so just replacing the 7i76e with 7i96 in the hal file should do the trick.
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 42
-
Thank you received: 4
-
-
28 May 2020 19:53 #169249
by msageryd
@tommylight: Yes, and thanks!!
When I read your question I got confused. I don't have a 7i76, but a 7i96.
It's probably a bug in the new pncconfig which leaves the wrong device name in the ini file. I corrected the name and now it works.
From the corrected ini file:
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 16940
-
Thank you received: 4345
-
-
28 May 2020 19:54 #169250
by PCW
This does seem to be fixed in the latest 2.8 (at least it works for me)
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 42
-
Thank you received: 4
-
-
Less
More
-
Posts: 16940
-
Thank you received: 4345
-
-
28 May 2020 20:15 #169253
by PCW
Maybe it a buildbot thing but I just fetched and rebuilt and there is no issue
The following user(s) said Thank You:
msageryd Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 17810
-
Thank you received: 5925
-
-
28 May 2020 21:45 #169256
by tommylight
@tommylight: Yes, and thanks!!
When I read your question I got confused. I don't have a 7i76, but a 7i96.
The title said 7i76e, the error said the same thing, so i came to the conclusion you have a 7i76e!
Walks like a duck, quacks like a duck, it s a duck !
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 2235
-
Thank you received: 475
-
-
29 May 2020 06:30 #169268
by Clive S
Walks like a duck, quacks like a duck, it s a duck !
I think you are understanding English too well now Tom:woohoo:
Please Log in or Create an account to join the conversation.
-
Configuring LinuxCNC
-
PnCConf Wizard
-
parameter or pin 'hm2_7i76e.0.watchdog.timeout_ns' not found
Time to create page: 0.115 seconds
