Deckel FP4A Retrofit

More
1 year 6 months ago #325556 by Beovoxo
Replied by Beovoxo on topic Deckel FP4A Retrofit

Attachment not found



The big screen turned out really nice :) so next step is to make the keyboard shelf ready and alot of push bottoms:)

Please Log in to join the conversation.

More
1 year 6 months ago #325632 by Beovoxo
Replied by Beovoxo on topic Deckel FP4A Retrofit
Keyboard frame almost ready for surface plates.

Attachment not found

Attachment not found

Attachment not found

Attachment not found

Attachment not found

Please Log in to join the conversation.

More
1 year 6 months ago #325768 by Beovoxo
Replied by Beovoxo on topic Deckel FP4A Retrofit
Frame ready for a steel sheet
 

Attachment not found

Please Log in to join the conversation.

More
1 year 6 months ago #326283 by Beovoxo
Replied by Beovoxo on topic Deckel FP4A Retrofit
Keyboard bracket finished with room for extra bottoms and trackpad. 

Attachment not found

 

Attachment not found

 

Attachment not found

 

Attachment not found

 

Attachment not found

 

Attachment not found

Please Log in to join the conversation.

More
1 year 6 months ago #326284 by Beovoxo
Replied by Beovoxo on topic Deckel FP4A Retrofit
Used keyboard matrix controller for bottoms on the controller cabinet. 
I disassemble a old keyboard and salvage the controller. the connection points has to be cleaned before soldering wires on it. "the black stuff" on the contact points are graphite with normal traces under.  

Attachment not found

Attachment not found

Attachment not found

Attachment not found

Attachment not found

Attachment not found

Please Log in to join the conversation.

More
1 year 6 months ago #326318 by Beovoxo
Replied by Beovoxo on topic Deckel FP4A Retrofit
Usb keyboard controller soldered with a RJ45 cable. I just used a lot of flux and let the soldering iron moved over all the contact points to start with. After this i pre tinned the wires and soldered them on. There is a bit of cleaning with isopropyl alcohol and sealing left, before its finished. 

Attachment not found

Attachment not found

Attachment not found

Please Log in to join the conversation.

More
1 year 6 months ago #326517 by Beovoxo
Replied by Beovoxo on topic Deckel FP4A Retrofit
Control cabinet almost finished. I just need to install 20 push buttons and connect them to the usb matrix board. I will mount a new keyboard with a trackball also.

Attachment not found

Attachment not found

Please Log in to join the conversation.

More
1 year 6 months ago #326763 by Beovoxo
Replied by Beovoxo on topic Deckel FP4A Retrofit
Got the lube pump, hydraulic pump, coolant pump testes and tempeary wired up. And got most of the wires from the spindle motor, transmission,  lube pump, hydraulic pump, coolant pump and the spindle brake wired to DIN terminal.
Also i made a DIN rail in the control cabinet. 
I did also some test on the software.
 

Attachment not found

Attachment not found

Attachment not found

Attachment not found

Attachment not found

Please Log in to join the conversation.

More
1 year 5 months ago #328814 by Beovoxo
Replied by Beovoxo on topic Deckel FP4A Retrofit
Electrical Cabinet makeover. 


Attachment not found

Attachment not found

Attachment not found

Attachment not found

Attachment not found

Attachment not found

Attachment not found



 

Please Log in to join the conversation.

More
1 year 5 months ago #329100 by Beovoxo
Replied by Beovoxo on topic Deckel FP4A Retrofit
Cabinet almost ready for sand blasting and paint. 

Attachment not found

Attachment not found

Please Log in to join the conversation.

Time to create page: 0.094 seconds
Powered by Kunena Forum