LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)

More
3 years 4 months ago #273999 by meister
Replied by meister on topic LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)
We have a very simple bob-adapter now for the TangNano9K Board:

github.com/multigcs/LinuxCNC-RIO/tree/main/configs/TangNano9K
 

Attachment not found

 

Attachment not found



 

Please Log in to join the conversation.

More
3 years 4 months ago #274160 by cakeslob
Replied by cakeslob on topic LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)
Hey, any thoughts on making it configurable via SD card config like the regular remora? I notice the tang has an SD card slot

Please Log in to join the conversation.

More
3 years 4 months ago #274163 by meister
Replied by meister on topic LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)
no, if you change the config (IO-Functions), you have to generate a new bit-file.
it's far away from remora, only the linux-component is adapted from remora.

Please Log in to join the conversation.

More
3 years 3 months ago #274682 by MaxEkb77
Replied by MaxEkb77 on topic LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)
Really cool project, try to use it

Please Log in to join the conversation.

More
3 years 3 months ago #274684 by meister
Replied by meister on topic LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)
Thank you !

which board do you have ?

greetings, Olli

Please Log in to join the conversation.

More
3 years 3 months ago #274692 by MaxEkb77
Replied by MaxEkb77 on topic LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)
tang 9k & pi (orange & raspberry), table pick&place for test.

How about w5500 for link normal computer ?

Please Log in to join the conversation.

More
3 years 3 months ago #274694 by meister
Replied by meister on topic LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)

How about w5500 for link normal computer ?
 


because there is no softcore running on the FPGA it is difficult to connect such interfaces.

but you can use one of this two modules to add UDP support:

github.com/multigcs/LinuxCNC-RIO/tree/main/UDP2SPI-Bridge

Please Log in to join the conversation.

More
3 years 3 months ago #274697 by MaxEkb77
Replied by MaxEkb77 on topic LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)

because there is no softcore running on the FPGA it is difficult to connect such interfaces.

 
Ok np, next time.
flash & wiring ok - working.
Question:
Driver have pid? - why not standart linuxcnc pid ?
 

Please Log in to join the conversation.

More
3 years 3 months ago #274699 by meister
Replied by meister on topic LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)
Do you mean inside the linuxcnc-component ?
this is based on the remora component and it works for me ,
so no reason at the moment to change it :)

Please Log in to join the conversation.

More
3 years 3 months ago #274819 by meister
Replied by meister on topic LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)
New boards , one for the TangNano9K and the other is an 8input+8Output expansion board
all with Pluggable Terminal Blocks

 

Attachment not found




 

Please Log in to join the conversation.

Time to create page: 0.222 seconds
Powered by Kunena Forum