5Axis Kinetic from 2.8 on 2.7x

More
6 years 1 month ago #182665 by Aciera
Replied by Aciera on topic 5Axis Kinetic from 2.8 on 2.7x
Not a problem, its just telling you that you already have the most recent version installed. So its something else that is missing.

Please Log in to join the conversation.

More
6 years 1 month ago #182666 by Aciera
Replied by Aciera on topic 5Axis Kinetic from 2.8 on 2.7x
Maybe this:

sudo apt-get install mesa-common-dev

and

sudo apt-get install libglu1-mesa-dev

and

sudo apt-get install libxmu-dev

Please Log in to join the conversation.

More
6 years 1 month ago #182667 by JackRay
Replied by JackRay on topic 5Axis Kinetic from 2.8 on 2.7x
and what?

Please Log in to join the conversation.

More
6 years 1 month ago #182710 by JackRay
Replied by JackRay on topic 5Axis Kinetic from 2.8 on 2.7x
Hello , it's good this message ...

Attachment not found

Please Log in to join the conversation.

More
6 years 1 month ago #182712 by Aciera
Replied by Aciera on topic 5Axis Kinetic from 2.8 on 2.7x
Very good indeed!

So next is

make

and if that works

sudo make setuid

Please Log in to join the conversation.

More
6 years 1 month ago #182713 by JackRay
Replied by JackRay on topic 5Axis Kinetic from 2.8 on 2.7x
What do you think about ?

Attachment not found

Please Log in to join the conversation.

More
6 years 1 month ago #182733 by Aciera
Replied by Aciera on topic 5Axis Kinetic from 2.8 on 2.7x
If all went well you should be able to start your RIP install:

source ../scripts/rip-environment

cd ..

linuxcnc

Once this works you can go back to this:

Warning: Spoiler!

Please Log in to join the conversation.

More
6 years 1 month ago #182750 by JackRay
Replied by JackRay on topic 5Axis Kinetic from 2.8 on 2.7x
I think everything went well, I have no mistakes. I have now a version 2.9.0.

But what should I do.

The goal of all this is to do 5 axes simultaneously.

Thank you again for your help, I didn't understand everything, but I had times where I thought we would not make it

Attachment not found

Please Log in to join the conversation.

More
6 years 1 month ago #182759 by Aciera
Replied by Aciera on topic 5Axis Kinetic from 2.8 on 2.7x
What does this say?

git branch | grep \*


If it says switch-kins then you should have the version that can switch kinematics.


So:

1. copy your machine configuration folder into the folder ~/linuxcnc-dev/config

you should be able to start your machine.

If this works we can continue to setup the switch-kins command.

Remember when you start a new terminal window you have to set you environment again by

cd ~/linuxcnc-dev/src
source ../scripts/rip-environment
cd ..
linuxcnc

Please Log in to join the conversation.

More
6 years 1 month ago #182823 by JackRay
Replied by JackRay on topic 5Axis Kinetic from 2.8 on 2.7x
Ok thank you ,

then I do a "Launcher" on my desktop to start version 2.9

Please Log in to join the conversation.

Time to create page: 0.167 seconds
Powered by Kunena Forum