- Posts: 34
- Thank you received: 0
8i20 cold start over current error
9 years 9 months ago #86588
by ZincBoy
Replied by ZincBoy on topic 8i20 cold start over current error
The faults never show up in the test system do they 
I checked the board version and it has "art rev D" on it so I think it is the same as you are using.
The output of the command you mentioned is:
When linuxcnc is running.
I checked the board version and it has "art rev D" on it so I think it is the same as you are using.
The output of the command you mentioned is:
Code:
12 float RW 1 hm2_5i25.0.8i20.0.1.angle-maxlim
12 float RW 0 hm2_5i25.0.8i20.0.1.angle-minlim
12 float RW 1 hm2_5i25.0.8i20.0.1.angle-scalemax
12 float RW 655.35 hm2_5i25.0.8i20.0.1.bus-voltage-scalemax
12 float RW 65535 hm2_5i25.0.8i20.0.1.card-temp-scalemax
12 float RW 5 hm2_5i25.0.8i20.0.1.current-maxlim
12 float RW -5 hm2_5i25.0.8i20.0.1.current-minlim
12 float RW 5 hm2_5i25.0.8i20.0.1.current-scalemax
12 u32 RO 0x000084D0 hm2_5i25.0.8i20.0.1.nvbrakeoffv
12 u32 RO 0x00008CA0 hm2_5i25.0.8i20.0.1.nvbrakeonv
12 u32 RO 0x00009664 hm2_5i25.0.8i20.0.1.nvbusoverv
12 u32 RO 0x00001194 hm2_5i25.0.8i20.0.1.nvbusundervmax
12 u32 RO 0x00000DAC hm2_5i25.0.8i20.0.1.nvbusundervmin
12 u32 RO 0x00000000 hm2_5i25.0.8i20.0.1.nvkdihi
12 u32 RO 0x00007D00 hm2_5i25.0.8i20.0.1.nvkdil
12 u32 RO 0x0000C350 hm2_5i25.0.8i20.0.1.nvkdilo
12 u32 RO 0x00000032 hm2_5i25.0.8i20.0.1.nvkdp
12 u32 RO 0x00000000 hm2_5i25.0.8i20.0.1.nvkqihi
12 u32 RO 0x00007D00 hm2_5i25.0.8i20.0.1.nvkqil
12 u32 RO 0x0000C350 hm2_5i25.0.8i20.0.1.nvkqilo
12 u32 RO 0x00000032 hm2_5i25.0.8i20.0.1.nvkqp
12 u32 RO 0x000002EE hm2_5i25.0.8i20.0.1.nvmaxcurrent
12 u32 RO 0x00000009 hm2_5i25.0.8i20.0.1.nvrembaudrate
12 u32 RO 0x0000008B hm2_5i25.0.8i20.0.1.swrevision
12 u32 RO 0x0A000020 hm2_5i25.0.8i20.0.1.unitnumber
Please Log in to join the conversation.
Time to create page: 0.067 seconds