Boxford 125 lathe Tool Changer Comp FERROR (SOLVED)

More
6 years 1 week ago #186899 by Clive S
Boxford 125 lathe Tool Changer Comp FERROR (SOLVED) was created by Clive S
I have started a new post to keep all the is one place.
I started looking at this:- forum.linuxcnc.org/38-general-linuxcnc-q...anger-setup?start=20

That is using this:- wiki.linuxcnc.org/cgi-bin/wiki.pl?Contri...oolchanger_component

Now this seems an old comp. I have tried to follow all the instructions from the readme in the boxford.tar.gz.

The Lathe does not have any sensors on the ATC it is an 8 position changer that only goes in one direction but then reverses a small amount to lock it. ... According to the above the segments are not equal at 45' they vary slightly between odd and equal numbers. ie. All odds are the same and all equals are the same.
.
Q1. Will the Carousel comp be better to work with this. linuxcnc.org/docs/2.8/html/man/man9/carousel.9.html
.
I have not used an A axis before so might not have set it up correctly. I have set is up as angular degrees but am getting following errors. no matter what I change in the ini file. I have tried changing MAX_VELOCITY - MAX_ACCELERATION - STEPGEN_MAXACCEL - FERROR - SCALE etc. the error always seems to be 1.3mm

I don't see a way to set it up with stepconf foa a lathe with A axis
.
I have attached the complete config in the rar file and the hal and ini files as well.

I have had to change quite a bit of the original files because they were from 2.4 era and pins have changed.

I am now using 2.7.14 but also have tried 2.8.

Attachment not found


Attachment not found

Attachment not found

Attachment not found

Please Log in to join the conversation.

More
6 years 6 days ago #187110 by Clive S
Replied by Clive S on topic Boxford 125 lathe Tool Changer Comp FERROR
Bump. No replies

Please Log in to join the conversation.

More
6 years 6 days ago #187114 by PCW
Replied by PCW on topic Boxford 125 lathe Tool Changer Comp FERROR
This suggests that the tool changer component has large steps in its position output.
You might just set both ferror limits to 10 or so and let the stepgens acceleration
limit smooth out the motion...

Please Log in to join the conversation.

More
6 years 6 days ago #187119 by Clive S
Replied by Clive S on topic Boxford 125 lathe Tool Changer Comp FERROR

PCW wrote: This suggests that the tool changer component has large steps in its position output.
You might just set both ferror limits to 10 or so and let the stepgens acceleration
limit smooth out the motion...


Ok I have changed
[AXIS_A]

TYPE = ANGULAR
#HOME = 0.0
MAX_VELOCITY = 0.005
MAX_ACCELERATION = 5
STEPGEN_MAXACCEL = 200
SCALE = 160
FERROR = 1 To 10 and 20
MIN_FERROR = 0.25 To 10 and 20
MIN_LIMIT = -99999
MAX_LIMIT = 99999
#HOME_OFFSET = 0.0

Same result, it immediately errors and moves the same amount 1.001. Not sure if this is in degrees or linear

Thanks for the help.

Edit; I have tried setting ferror to 50 as well.

Please Log in to join the conversation.

More
6 years 6 days ago #187120 by PCW
Replied by PCW on topic Boxford 125 lathe Tool Changer Comp FERROR
A ferror?
What happens if you set the ferrors to 1000?

Please Log in to join the conversation.

More
6 years 6 days ago #187121 by Clive S
Replied by Clive S on topic Boxford 125 lathe Tool Changer Comp FERROR

PCW wrote: A ferror?
What happens if you set the ferrors to 1000?


No change using a 1000.
Where would I find ferror in hal config? as I don't see it anywhere . only in the ini file

Edit: In the hal file I have stepgens 0, then 2,3 so 1 is missing. configs are in the first post. Could it be that is is not reading the correct part of the hal

Please Log in to join the conversation.

More
6 years 6 days ago #187122 by PCW
Replied by PCW on topic Boxford 125 lathe Tool Changer Comp FERROR
its in the ini file

Can you plot the tool changer position command?
Does it really have a 1000 degree step?

Please Log in to join the conversation.

More
6 years 6 days ago #187123 by Clive S
Replied by Clive S on topic Boxford 125 lathe Tool Changer Comp FERROR

PCW wrote: its in the ini file

Can you plot the tool changer position command?
Does it really have a 1000 degree step?


I have done an edit in the previous post.

I will try and do a plot in the morning . What do I plot the tool changer command against for the trigger

I have to stop now have been called for dinner. thanks again

Please Log in to join the conversation.

More
6 years 5 days ago #187183 by Clive S
Replied by Clive S on topic Boxford 125 lathe Tool Changer Comp FERROR

Clive S wrote:

PCW wrote: its in the ini file

Can you plot the tool changer position command?
Does it really have a 1000 degree step?


I have done an edit in the previous post.

I will try and do a plot in the morning . What do I plot the tool changer command against for the trigger

I have to stop now have been called for dinner. thanks again


Re: Does it really have a 1000 degree step? not sure what you mean by this.

This is the first plot with the ferror at 1000 and min_ferror at 1000

Attachment not found


.
then the second ferror at 1000 and min_ferror at 1000

Attachment not found


.
The next 3 are with ferror at 1 and min_ferror at 0.5

Attachment not found


.
The they are like this until the DRO gets up to 21.7 I am pressing F2 to run between the errors

Attachment not found


.
Now it is 21.7 on the DRO I think this is the final position where the turret should be. (I am doing this on the bench ie no physical machine).
.

Attachment not found

Please Log in to join the conversation.

More
6 years 3 days ago #187413 by Clive S
Replied by Clive S on topic Boxford 125 lathe Tool Changer Comp FERROR
I can't seem to get further on this The A axis will not move further that 1 unit then it will ferror

Code:
[AXIS_A] TYPE = ANGULAR HOME = 0.0 MAX_VELOCITY = 1 MAX_ACCELERATION = 5 STEPGEN_MAXACCEL = 5 SCALE = 80 FERROR = 1 MIN_FERROR = 0.5 MIN_LIMIT = -99999 MAX_LIMIT = 99999 HOME_OFFSET = 0.0 setp stepgen.3.position-scale [AXIS_A]SCALE setp stepgen.3.steplen 1 setp stepgen.3.stepspace 0 setp stepgen.3.dirhold 35000 setp stepgen.3.dirsetup 35000 setp stepgen.3.maxaccel [AXIS_A]STEPGEN_MAXACCEL #net apos-cmd axis.3.motor-pos-cmd => stepgen.3.position-cmd #net apos-fb stepgen.3.position-fb => axis.3.motor-pos-fb net astep <= stepgen.3.step net adir <= stepgen.3.dir net aenable axis.3.amp-enable-out => stepgen.3.enable ########################################################### # loading the toolchange component in .hal file ########################################################### loadrt toolchanger addf toolchanger servo-thread net tool-change iocontrol.0.tool-change => toolchanger.toolchange net tool-changed iocontrol.0.tool-changed <= toolchanger.toolchanged net tool-number iocontrol.0.tool-prep-number => toolchanger.toolnumber net tool-oldnumber iocontrol.0.tool-number => toolchanger.currenttoolnumber net apos-cmd toolchanger.position-cmd => stepgen.3.position-cmd net ahomed axis.3.homed => toolchanger.ishomed net tool-prepare-loopback iocontrol.0.tool-prepare => iocontrol.0.tool-prepared

Has anybody got a working config for an angular A axis

Am I using the wrong axis letter for the turret?

Attachment not found

Please Log in to join the conversation.

Time to create page: 0.178 seconds
Powered by Kunena Forum