[SOLVED] Mesa 7i80HD-16: startup errors

More
5 years 10 months ago #191736 by travis036
Replied by travis036 on topic Mesa 7i80HD-16: startup errors
couldn't find mesaflash on my linuxcnc machine. downloaded it from Mesa, but it is windows, so i booted my windows machine, and tried the command, but it didn't like it. i did manage this though, if it is the correct info.
Code:
./mesaflash.exe --device 7i80 --rpo 192.168.1.121 --verbose board name: 7I80HD-16 LBP16 address spaces: 0: HostMot2 (registers, RW, 32-bit) [size=64K] 1: KSZ8851 (registers, RW, 16-bit) [size=256] 2: EtherEEP (EEPROM, RW, 16-bit) [size=128], page size: 0x1, erase size: 0x1 3: FPGAFlsh (flash, RW, 32-bit) [size=16M], page size: 0x100, erase size: 0x10000 6: LBP16RW (memory, RW, 16-bit) [size=16] 7: LBP16RO (memory, RO, 16-bit) [size=16] eth eeprom info: mac address: 00:60:1B:11:81:5D ip address: 192.168.1.121 board name: 7I80HD-16 user leds: eth debug FPGA flash eeprom info: flash id: 0x14 (size 16Mb) lba16 status/control info: packets recived: all 63153, UDP 3964, bad 0 packets sended: all 3523, UDP 3508, bad 0 parse errors: 0, mem errors 0, write errors 0 UDP time: 0 board info: board name: 7I80HD-16 LBP16 version 3 firmware version 15 IP address jumpers at boot: fixed 192.168.1.121 firmware info: cookie: 55AACAFE name: HOSTMOT2 IDROM version: 3 Module 0: Watchdog, version 0 [instances=1] Module 1: IOPort, version 0 [instances=3] Module 2: Muxed Encoder, version 3 [instances=6] Module 3: Muxed Encoder Select, version 0 [instances=1] Module 4: PWMGen, version 0 [instances=6] Module 5: Smart Serial Interface, version 0 [instances=1] Module 6: LED, version 0 [instances=1] 0xFFFFFFFF

~Travis

Please Log in to join the conversation.

More
5 years 10 months ago #191741 by travis036
Replied by travis036 on topic Mesa 7i80HD-16: startup errors
Code:
./mesaflash.exe --device 7i80 --ip 192.168.1.121 --verbose --write ./7i80hd_16_st12.bit board name: 7I80HD-16 LBP16 address spaces: 0: HostMot2 (registers, RW, 32-bit) [size=64K] 1: KSZ8851 (registers, RW, 16-bit) [size=256] 2: EtherEEP (EEPROM, RW, 16-bit) [size=128], page size: 0x1, erase size: 0x1 3: FPGAFlsh (flash, RW, 32-bit) [size=16M], page size: 0x100, erase size: 0x10000 6: LBP16RW (memory, RW, 16-bit) [size=16] 7: LBP16RO (memory, RO, 16-bit) [size=16] eth eeprom info: mac address: 00:60:1B:11:81:5D ip address: 192.168.1.121 board name: 7I80HD-16 user leds: eth debug FPGA flash eeprom info: flash id: 0x14 (size 16Mb) lba16 status/control info: packets recived: all 64530, UDP 4015, bad 0 packets sended: all 3575, UDP 3559, bad 0 parse errors: 0, mem errors 0, write errors 0 UDP time: 0 board info: board name: 7I80HD-16 LBP16 version 3 firmware version 15 IP address jumpers at boot: fixed 192.168.1.121 firmware info: cookie: 55AACAFE name: HOSTMOT2 IDROM version: 3 Module 0: Watchdog, version 0 [instances=1] Module 1: IOPort, version 0 [instances=3] Module 2: Muxed Encoder, version 3 [instances=6] Module 3: Muxed Encoder Select, version 0 [instances=1] Module 4: PWMGen, version 0 [instances=6] Module 5: Smart Serial Interface, version 0 [instances=1] Module 6: LED, version 0 [instances=1] Checking file... OK File type: BIT file Design name: TopEthernetHostMot2b.ncd;UserID=0xFFFFFFFF Part name: 6slx16ftg256 Design date: 2014/09/14 Design time: 18:27:46 Config Length: 464196 Boot sector OK EEPROM sectors to write: 7, max sectors in area: 16 Erasing EEPROM sectors starting from 0x100000... |EEEEEEEE Programming EEPROM sectors starting from 0x100000... |WWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWW Board configuration verified successfully

ok, now what? (sorry for being fairly clueless)

~Travis

Please Log in to join the conversation.

More
5 years 10 months ago #191756 by travis036
Replied by travis036 on topic Mesa 7i80HD-16: startup errors
in all honesty, i don't even know if i wrote the correct flash... i assumed st12 was for stepper...
there are no pin files with any of the configurations.

~Travis

Please Log in to join the conversation.

More
5 years 10 months ago #191757 by tommylight
Replied by tommylight on topic Mesa 7i80HD-16: startup errors

travis036 wrote: ok, now what?

Switch to Linux and test again ! :)
Also, report back how that goes.

Please Log in to join the conversation.

More
5 years 10 months ago #191763 by travis036
Replied by travis036 on topic Mesa 7i80HD-16: startup errors
still same error...
i scrapped the former config, and tried a new one, but when i load the 7i80 data, from "/lib/firmware/hm2/7i80hd_16" (where i piled the Mesa BIT files), i get the following error when i try to accept changes.

Attachment not found



so i assume i have yet again screwed something up...

~Travis

Please Log in to join the conversation.

More
5 years 10 months ago #191766 by tommylight
Replied by tommylight on topic Mesa 7i80HD-16: startup errors
There is no need to load or use any firmware now, just do a config, save and close pncconf, and start that config.

Please Log in to join the conversation.

More
5 years 10 months ago #191774 by travis036
Replied by travis036 on topic Mesa 7i80HD-16: startup errors
still getting errors...

Please Log in to join the conversation.

More
5 years 10 months ago #191775 by PCW
Replied by PCW on topic Mesa 7i80HD-16: startup errors
Looks like the same firmware
Did you reset the 7I80 after loading the new firmware?

Please Log in to join the conversation.

More
5 years 10 months ago #191776 by travis036
Replied by travis036 on topic Mesa 7i80HD-16: startup errors
no, didn't know i was supposed to... :unsure:
just power-cycled it, and i get a new error. my guess is i picked a firmware with no PWM

Please Log in to join the conversation.

More
5 years 10 months ago #191777 by PCW
Replied by PCW on topic Mesa 7i80HD-16: startup errors
Yes, a ST12 config would not have any PWMgens

Mesaflash should have printed a message that you need to power
cycle the board or used the "reload" command to use the new firmware

Please Log in to join the conversation.

Time to create page: 0.131 seconds
Powered by Kunena Forum