7i76E Spindle configuration

Houston !!! i have a problem!!! 

Is the networking set up for Mesa?
Is the IP address on the board set same as in the config?

Yes, the sample file is set for a 10.10.10.10 IP address
if you are using 192.168.1.121, you will get that error
 

I was able to correct the IP address
it doesn't work, I can set cw-cww-enable but no speed.
I am trying to update and it cannot find the linuxcnc repository , gives an error
I am using 2.9.5

Should I reinstall everything again?
I don't understand what is happening

You should be able to debug spindle operation by using halshow
to look at the spindle pins as you set the spindle speed to different values
Important things to watch are:

hm2_7i76e.0.7i76.0.0.spinout-minlim  
hm2_7i76e.0.7i76.0.0.spinout-maxlim   
hm2_7i76e.0.7i76.0.0.spinout-scalemax 
hm2_7i76e.0.7i76.0.0.spinena-invert  

 hm2_7i76e.0.7i76.0.0.spinout
hm2_7i76e.0.7i76.0.0.spinena


Also make sure then the electrical connections are correct
(so you have 10V from SPIN+ to SPIN-)

drive.google.com/file/d/1lh_3pexmAgHTyC0.../view?usp=drive_link

Could it be that I am not using the correct version of LinuxCNC?



 

Could it be that I am not using the correct version of LinuxCNC?

No, any version of LinuxCNC from 2.8 on will work with the 7I76E

Like I said you need to check


hm2_7i76e.0.7i76.0.0.spinout-minlim  
hm2_7i76e.0.7i76.0.0.spinout-maxlim   
hm2_7i76e.0.7i76.0.0.spinout-scalemax 
hm2_7i76e.0.7i76.0.0.spinena-invert  

 hm2_7i76e.0.7i76.0.0.spinout
hm2_7i76e.0.7i76.0.0.spinena

with halshow

In axis, you can run halshow with:

Machine --> Show Hal Configuration --> Watch

And also verify that you have +10V on the 7I76E SPINDLE+ pin
(TB4 pin 3) relative to SPINDLE- (TB4 pin 1)

 

wrote:

You may try 2.9.4 if you like.

www.linuxcnc.org/iso/linuxcnc_2.9.4-amd64.hybrid.iso

Your HDD probably has enough space to dual boot LinuxCNC 2.9.4 and 2.9.4.

Why? What's the point of having two of the same version?

I think it may have been a typo, but even then, there is a far better way to have multi versions of Linuxcnc, that's the beauty of building from source, if you can follow instructions you can do it, and taking advantage of the run in place facility, aka RIP.

Videos 7i76e spindle failure  
thankkkkkkkssssss !!!!!!
I have performed all the tests before starting the forum. It does not output 10 VCC, it does not regulate voltage, that's why I started the thread.
I am confused with this situation, the board was working perfectly on a lathe with version 2.7.15. Now I need to install it on another machine. I tried 2.8 - 2.9.4 - 2.9.5 the result is always the same, it does not regulate voltage. But there is something that is not connecting, linuxcnc shows good operation in Halshow, but it does not go out through the 7i76e.

I am going to reinstall linuxcnc from scratch again and see what happens.
thank you all for trying to help me!!! I'll post updates soon!!!