Mint 19.3 Linuxcnc Odroid H2+

>Main >Advanced >ACPI Settings ACPI Sleep State = [Suspend Disabled] >Smart Settings SMART Self Test = [Disabled] >Serial Port Consol Redirection Com0 Consol Redirection = [Disabled] >Consol Redirection Settings Com1 Consol Redirection = [Disabled] >Consol Redirection Settings >Legacy Console Redirection Settings Redirection COM Port = [COM0] Resolution = [80x24] Redirect After Post = [Always Enable] Serial Port for Out-of-Band Management/ Windows Emergency Management Service (EMS) Consol Redirection = [Disabled] >CPU Configuration >CPU Power Management EIST = [Enabled] Turbo Mode = [Enabled] Boot performance mode = [Max Performance] Active Processor Cores = [Enabled] Core 0 = [Enabled] Core 1 = [Enabled] Core 2 = [Enabled] Core 3 = [Enabled] Intel Virtualization Technology = [Disabled] VT-d = [Disabled] >SIO Configuration >[*Active*] Serial Port 1 >[*Active*] Serial Port 2 >Network Stack Configuration Network Stack = [Enabled] Ipv4 PXE = Support = [Enabled] Ipv4 HTTP Support = [Disabled] Ipv6 PXE = Support = [Enabled] Ipv6 HTTP Support = [Disabled] PXE boot wait time = 0 Media detect count = 2 >NVMe Configuration > Samsung SSD 970 EVO Plus 250GB >USB Configuration >Realtek PCIe 2.5GBE Family Controller >Realtek PCIe 2.5GBE Family Controller >Thermal >Chipset >North Bridge Max TOLUD = [2GB] >South Bridge OS Selection = [Intel Linux] >Uncore Configuration GTT Size = [8MB] Aperture Size = [256MB] DVMT Pre-Allocated = [64M] DVMT Total Gfx Mem = [256M] Cd Clock Frequency = [316.8 MHz] GT PM Support = [Enable] PAVP Enable = [Enable] ASMF = [Disable] >South Cluster Configuration >HD-Audio Configuration HD-Audio Spport = [Disable] HD-Audio DSP = [Disable] HD-Audio CSME Memory Transfers = [VCO] HD-Audio Host Memory Transfers = [VCO] HD-Audio I/O Buffer Ownership Sele = [HD-Audio Link owns ...] HD-Audio Clock Gating = [Disable] HD-Audio Power Gating = [Disable] HD-Audio PME = [Disable] HD-Audio Link Frequency = [24 MHz] iDisplay Link Frequency = [96 MHz] >LPSS Configuration LPSS I2C #6 Support (D23:F1) = [PCI Mode] Set LPSS I2C #6 Speed = [400KHz] LPSS I2C #7 Support (D23:F1) = [PCI Mode] Set LPSS I2C #7 Speed = [400KHz] >PCI Express Configuration PCI Express Clock Gating = [Enabled] PCIE Port assignment to LAN = 1,2 Port8xh Decode = [Disabled] Peer Memory Write = [Enabled] Compliance Mode = [Enabled] > PCI Express Root Port 1 ASPM = [Disabled] L1 Substates = [L1.1 & L1.2] ACS = [Enabled] URR = [Disable] FER = [Disable] NFER= [Disable] CER = [Disable] CTO = [Disabled] SEFE = [Disable] SENFE = [Disable] SECE = [Disabled] PME SCI = [Enable] Hot Plug = [Disable] PCIe Speed = [Auto] Transmitter Half Swing = [Disable] Extra Bus Reserved = 0 Reserved Memory = 10 Reserved I/O = 4 PCH PCIe LTR Configuration PCH PCIE LTR = [Enabled] Snoop Latency Override = [Auto] Non Snoop Latency Override = [Auto] PCIE LTR LOCK = [Disabled] PCIe Selectable D-emphasis = [Enabled] > PCI Express Root Port 2 (Set same as Port 1) > PCI Express Root Port 3 (Set same as Port 1) > PCI Express Root Port 4 (Set same as Port 1) > PCI Express Root Port 5 (Set same as Port 1) > PCI Express Root Port 6 (Set same as Port 1) >SATA Drives Chipset -SATA Controller Configuration Chipset SATA = [Enable] SATA Mode Selection [ACHI] SATA Test Mode = [Disabled] Aggressive LPM Support = [Enabled] SATA Port 0 = [Not Installed] SATA Port 1 = [Not Installed] >SCC Configuration SCC eMMC Support (D38:F0) = [Enabled] eMMC Max Speed = [HS400] SCC UFS Support (D29:F0) = [Disable] >USB Configuration XCHI Pre-Boot Driver = [Disable] xHCI Mode = [Enable] USB VBUS = [ON] XHCI Disable Compliance Mode = [TRUE] >Miscellaneous Configuration State After G3 = [S5 State] Wake On Lan = [Enable] >Security Secure Boot >Boot Setup Prompt Timeout = [1] Bootup NumLock State = [Off] Quiet Boot = [Enabled] Boot Option Priorities Boot Option #1 = [ubuntu (Samsung SSD...)] Boot Option #2 = [UFEI: PXE IP4 Realt...] Boot Option #3 = [UFEI: PXE IP4 Realt...] Boot Option #4 = [UFEI: PXE IP4 Realt...] Boot Option #5 = [UFEI: PXE IP4 Realt...] Fast Boot = [Disable] New Boot Option Policy = [Default] Save & Exit