Installing LCNC on Beelink BT3 PRO II

htdave
Topic Author
Offline
Senior Member

5 years 4 months ago #211086 by htdave

Replied by htdave on topic Installing LCNC on Beelink BT3 PRO II

I think Mint 19.3 is a better option.

Would you go Mate or XFCE?

Please Log in to join the conversation.

BeagleBrainz
New Member

5 years 4 months ago #211089 by BeagleBrainz

Replied by BeagleBrainz on topic Installing LCNC on Beelink BT3 PRO II

XFCE is lighter on resources.

Please Log in to join the conversation.

htdave
Topic Author
Offline
Senior Member

5 years 4 months ago #211109 by htdave

Replied by htdave on topic Installing LCNC on Beelink BT3 PRO II

I have just finished installing mint 19 xfce, using the step by step from Tommylight.

When I boot with RT, the system lacks stability.

When I type lspci -vn, I get:

Code:

lagunmatic@lagunmatic:~$ lspci -vn
00:00.0 0600: 8086:2280 (rev 36)
	Subsystem: 8086:7270
	Flags: bus master, fast devsel, latency 0
	Kernel driver in use: iosf_mbi_pci

00:02.0 0300: 8086:22b0 (rev 36) (prog-if 00 [VGA controller])
	Subsystem: 8086:7270
	Flags: bus master, fast devsel, latency 0, IRQ 300
	Memory at 90000000 (64-bit, non-prefetchable) [size=16M]
	Memory at 80000000 (64-bit, prefetchable) [size=256M]
	I/O ports at f000 [size=64]
	[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel driver in use: i915
	Kernel modules: i915

00:03.0 0480: 8086:22b8 (rev 36)
	Subsystem: 8086:7270
	Flags: fast devsel, IRQ 255
	Memory at 91000000 (32-bit, non-prefetchable) [disabled] [size=4M]
	Capabilities: <access denied>

00:0b.0 1180: 8086:22dc (rev 36)
	Subsystem: 8086:7270
	Flags: fast devsel, IRQ 301
	Memory at 9193b000 (64-bit, non-prefetchable) [size=4K]
	Capabilities: <access denied>
	Kernel driver in use: proc_thermal
	Kernel modules: processor_thermal_device

00:14.0 0c03: 8086:22b5 (rev 36) (prog-if 30 [XHCI])
	Subsystem: 8086:7270
	Flags: bus master, medium devsel, latency 0, IRQ 299
	Memory at 91900000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: <access denied>
	Kernel driver in use: xhci_hcd
	Kernel modules: xhci_pci

00:1a.0 1080: 8086:2298 (rev 36)
	Subsystem: 8086:7270
	Flags: bus master, fast devsel, latency 0, IRQ 255
	Memory at 91700000 (32-bit, non-prefetchable) [size=1M]
	Memory at 91600000 (32-bit, non-prefetchable) [size=1M]
	Capabilities: <access denied>

00:1c.0 0604: 8086:22c8 (rev 36) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0, IRQ 297
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 0000e000-0000efff
	Memory behind bridge: 91800000-918fffff
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:1f.0 0601: 8086:229c (rev 36)
	Subsystem: 8086:7270
	Flags: bus master, medium devsel, latency 0
	Capabilities: <access denied>
	Kernel driver in use: lpc_ich
	Kernel modules: lpc_ich

01:00.0 0200: 10ec:8168 (rev 0c)
	Subsystem: 10ec:0123
	Flags: bus master, fast devsel, latency 0, IRQ 298
	I/O ports at e000 [size=256]
	Memory at 91804000 (64-bit, non-prefetchable) [size=4K]
	Memory at 91800000 (64-bit, prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: r8169
	Kernel modules: r8169

lagunmatic@lagunmatic:~$ 

Still no wifi

Any ideas?

Please Log in to join the conversation.

BeagleBrainz
New Member

5 years 4 months ago #211120 by BeagleBrainz

Replied by BeagleBrainz on topic Installing LCNC on Beelink BT3 PRO II

If you still have the Mint 19 installed could you try

Code:

dmesg | grep brcm > brcm.txt

I may not have made myself clear.

Boot into a live session of Mint 20 then run

Code:

lspci -vn > lspci.txt

and could you also try

Code:

dmesg | grep brcm > brcm.txt

and attached both text files.

I suggest this as due to your claim that Mint 20 gets you wifi.
The output of dmesg will also be useful.

When you say the system lacks stability what do you mean. What issues are presenting.

This is a link to the Mint 19 iso I created.
drive.google.com/file/d/1d7IEscVlyWoNZQe...s4D/view?usp=sharing

If you would like to test this for stability you are welcome to. Some of the repos no longer exist, but that is not the point. The point is to test if the kernel on this ISO will give you better/any stability. This will give you a full installation of Mint 19 with a PREEMPT kernel & linuxcnc.

Just had a look at the iso, the firmware is there for the wifi chip, all that is missing is the nvram text file.

If it is stable and you want to run with it we can sort the repos out as it is quite simple.

Or send the thing down to Sydney and I'll get it going by hell or high water :lol:

Oh ok this seems to be the same CPU that was used on the Atomic Pi, not exactly the fastest one out there. Even when I tried it with LXDE it wasn't the greatest

Sorry if this post is a bit all over the place, but I'm willing to answer any questions you have.

Please Log in to join the conversation.

tommylight
Offline
Administrator

5 years 4 months ago #211144 by tommylight

Replied by tommylight on topic Installing LCNC on Beelink BT3 PRO II

The thing with WiFi is, even if you make it work with the RT kernel it might mess up latency badly, so might need to disable it and use a WiFi dongle.

Please Log in to join the conversation.

BeagleBrainz
New Member

5 years 4 months ago #211146 by BeagleBrainz

Replied by BeagleBrainz on topic Installing LCNC on Beelink BT3 PRO II

Yeah that's a good point and what I was thinking regarding getting a dongle.

I just had a look in the /lib/firmware/brcm dir of Mint 19 & Mint 20 whilst Mint 19 has the bin files the txt files are missing.

Maybe copying the Mint 20 txt files to Mint 19 would get it working.

The wifi should work as it's the same that the RPi4 uses.

Please Log in to join the conversation.

BeagleBrainz
New Member

5 years 4 months ago #211154 by BeagleBrainz

Replied by BeagleBrainz on topic Installing LCNC on Beelink BT3 PRO II

Found this regarding nvram

wireless.wiki.kernel.org/en/users/drivers/brcm80211

Please Log in to join the conversation.

htdave
Topic Author
Offline
Senior Member

5 years 4 months ago #211286 by htdave

Replied by htdave on topic Installing LCNC on Beelink BT3 PRO II

I ended up installing 19.3 from an iso I had for my odroid - pretty sure it was from beaglebrainz.

It all runs fine except no WiFi. Perhaps I should just get a usb wifi - any suggestions on a decent one?

Jitter is not good - about 250,000 max. Is this way too high even for a mesa? Anything I should be doing to reduce jitter?

Is it worth persevering with this pc, or should i get something better? It is for a VMC that will be used in our manufacturing business, so needs to be reliable.

Thanks

Please Log in to join the conversation.

Clive S
Offline
Platinum Member

5 years 4 months ago #211287 by Clive S

Replied by Clive S on topic Installing LCNC on Beelink BT3 PRO II

No eBay APP ID and/or Cert ID defined in Kunena configuration

It all runs fine except no WiFi. Perhaps I should just get a usb wifi - any suggestions on a decent one?

I have bought several of these without any issues. I see they have gone up in price lately

Please Log in to join the conversation.

BeagleBrainz
New Member

5 years 4 months ago #211297 by BeagleBrainz

Replied by BeagleBrainz on topic Installing LCNC on Beelink BT3 PRO II

htdave wrote: I ended up installing 19.3 from an iso I had for my odroid - pretty sure it was from beaglebrainz.

It all runs fine except no WiFi. Perhaps I should just get a usb wifi - any suggestions on a decent one?

Jitter is not good - about 250,000 max. Is this way too high even for a mesa? Anything I should be doing to reduce jitter?

Is it worth persevering with this pc, or should i get something better? It is for a VMC that will be used in our manufacturing business, so needs to be reliable.

Thanks

Follow the link in this post to grab the nvram file.
forum.linuxcnc.org/9-installing-linuxcnc...o-ii?start=10#211154

Like I said Mint 19 has the firmware all that is missing is the text file.
The efivars filesystem should already be mounted.
For the jitter just the usual,
Turn off any power saving and you may also use the isolcpu kernel commandline option.
Mint works with just about any USB wifi dongle.

Please Log in to join the conversation.

Time to create page: 0.061 seconds