PlasmaC Fiber laser 1Kw head height control + auto focuas

There is one issue that I have just discovered. After PlasmaC senses the ohmic input it sends the torch to zero height which would touch the torch against the material. There is no need for it to do that so I will take a look at it tomorrow.

phillc54 wrote:

There is one issue that I have just discovered. After PlasmaC senses the ohmic input it sends the torch to zero height which would touch the torch against the material. There is no need for it to do that so I will take a look at it tomorrow.

This issue is now fixed.

phillc54 wrote: 2.8 and master. I see the 2.8 buildbot (stretch and buster) is up to date but master isn't yet. You can also build from source

phillc54 wrote: Any Run Panel pins that are linked in HAL are done in plasmac_run.hal

Warning: Spoiler!

Code:

#***** plasmac component *********************************************** net plasmac:axis-max-limit ini.z.max_limit => plasmac.axis-z-max-limit net plasmac:axis-min-limit ini.z.min_limit => plasmac.axis-z-min-limit #***** run page ******************************************************** # outputs net plasmac:cornerlock-enable plasmac_run.cornerlock-enable => plasmac.cornerlock-enable net plasmac:cut-feed-rate plasmac_run.cut-feed-rate-f => plasmac.cut-feed-rate net plasmac:cut-height plasmac_run.cut-height-f => plasmac.cut-height net plasmac:cut-volts plasmac_run.cut-volts-f => plasmac.cut-volts net plasmac:kerfcross-enable plasmac_run.kerfcross-enable => plasmac.kerfcross-enable net plasmac:mesh-enable-0 plasmac_run.mesh-enable => plasmac.mesh-enable-0 net plasmac:mesh-ignore-ok plasmac_run.mesh-ignore-ok => plasmac.mesh-ignore-ok net plasmac:ohmic-probe-enable plasmac_run.ohmic-probe-enable => plasmac.ohmic-probe-enable net plasmac:pause-at-end plasmac_run.pause-at-end-f => plasmac.pause-at-end net plasmac:pierce-delay plasmac_run.pierce-delay-f => plasmac.pierce-delay net plasmac:pierce-height plasmac_run.pierce-height-f => plasmac.pierce-height net plasmac:puddle-jump-delay plasmac_run.puddle-jump-delay-f => plasmac.puddle-jump-delay net plasmac:puddle-jump-height plasmac_run.puddle-jump-height-f => plasmac.puddle-jump-height net plasmac:thc-enable plasmac_run.thc-enable-out => plasmac.thc-enable net plasmac:use-auto-volts plasmac_run.use-auto-volts => plasmac.use-auto-volts

any plasmac_run.pins not listed above are manipulated directly by the code in plasmac_run.py

taloot wrote: another small issue
i will use 2 pwm to analog convertor (0-10v)
1 for laser
2 for gas valve
is it to linked to spindle control?
if yes can i load 2 spindles?

tommylight wrote:

taloot wrote: another small issue
i will use 2 pwm to analog convertor (0-10v)
1 for laser
2 for gas valve
is it to linked to spindle control?
if yes can i load 2 spindles?

Adding a resistor and a small capacitor to the PWM output will make it analogue, but only up to 5V if the PWM output is 5V.
Since you are using Mesa boards, you can use normal outputs for PWM but with very limited frequency, so if the frequency is not high the above idea might be useful.
That makes 3 PWM's !
It can be controlled as a spindle but it does not have to be, PWM's can be set on their own.And yes, you can have up to 8 spindles if i remember correctly in LinuxCNC 2.8 and Master.