PlasmaC Fiber laser 1Kw head height control + auto focuas

More
6 years 2 months ago #178497 by taloot
Replied by taloot on topic PlasmaC modification to fit fiber laser rs485 control head capacitance Autofou

tommylight wrote: This is what i use for the engravers i make, see here:
forum.linuxcnc.org/10-advanced-configura...-superimposing-a-pic
There is also the complete config there, but here is the important part:

Code:
loadrt pwmgen output_type=0 addf pwmgen.make-pulses base-thread addf pwmgen.update servo-thread setp pwmgen.0.enable TRUE #setp pwmgen.0.pwm-freq 1000 #setp pwmgen.0.scale 100 #setp pwmgen.0.offset 0 #setp pwmgen.0.min-dc 1 #setp pwmgen.0.max-dc 99 #setp pwmgen.0.dither-pwm true net analogout motion.analog-out-00 => pwmgen.0.value net laserpwm pwmgen.0.pwm => parport.0.pin-02-out
See also for more than one PWM
linuxcnc.org/docs/2.4/html/hal_rtcomps.html#sec:PWMgen

net laserpwm pwmgen.0.pwm => parport.0.pin-02-out

what is laserpwm mean in this example?
is it component or name or what

Please Log in to join the conversation.

More
6 years 2 months ago #178503 by tommylight
Replied by tommylight on topic PlasmaC modification to fit fiber laser rs485 control head capacitance Autofou
Just an arbitrary name .

Please Log in to join the conversation.

More
6 years 2 months ago #178624 by taloot
Replied by taloot on topic PlasmaC modification to fit fiber laser rs485 control head capacitance Autofou

Attachment not found



im having this error
and ideas?


***** my fault. its read only value*********

solved

Please Log in to join the conversation.

More
6 years 2 months ago #178780 by taloot
Replied by taloot on topic PlasmaC modification to fit fiber laser rs485 control head capacitance Autofou
testing machine max speed with 1mm ss
cutting gas normal air @ 190 psi


Please Log in to join the conversation.

More
6 years 2 months ago #178782 by phillc54
Replied by phillc54 on topic PlasmaC modification to fit fiber laser rs485 control head capacitance Autofou
Impressive...

Please Log in to join the conversation.

More
6 years 2 months ago #178783 by snowgoer540
Replied by snowgoer540 on topic PlasmaC modification to fit fiber laser rs485 control head capacitance Autofou
Holy crap that’s awesome. Need.

Please Log in to join the conversation.

More
6 years 2 months ago #178827 by tommylight
Replied by tommylight on topic PlasmaC modification to fit fiber laser rs485 control head capacitance Autofou
Very nice. Thank you.
Can do a video where LinuxCNC can also be seen, please ?

Please Log in to join the conversation.

More
6 years 2 months ago #178891 by taloot
Replied by taloot on topic PlasmaC modification to fit fiber laser rs485 control head capacitance Autofou

tommylight wrote: Very nice. Thank you.
Can do a video where LinuxCNC can also be seen, please ?


i making the userspace pin
and link the ARC OK <--- this will be link to laser status + monitor gas pressure if drop below workable pressure
and fix some issue with capacitance,, sensor i make,, its 3.3v pwm.. and it fails with long cable
and i will do complete test +
cut + marking
with ss its simple
gas on and laser on and machine keep moving

Please Log in to join the conversation.

More
6 years 2 months ago #179209 by taloot
Replied by taloot on topic PlasmaC modification to fit fiber laser rs485 control head capacitance Autofou


this is it working in simulator,,,

but i dont know how can i run the qtpyvcp embedded

Please Log in to join the conversation.

More
6 years 2 months ago #179210 by phillc54
Replied by phillc54 on topic PlasmaC modification to fit fiber laser rs485 control head capacitance Autofou
Looking good, did you try Qtvcp. I think that can be embedded similar to Gladevcp.

Please Log in to join the conversation.

Time to create page: 0.191 seconds
Powered by Kunena Forum