Raspberry Pi 4 with PlasmaC

tecno wrote: Is the Latency-Histogram disk intensive as I am running on a µSD card?

Not that i know of.

I will finalize all home switches + floating head and then start playing around more seriously and see what error I get if any.

What kind of ping times do you get if you ping the mesa card?

pi@pi4-mate:~ $ ping 10.10.10.10
PING 10.10.10.10 (10.10.10.10) 56(84) bytes of data.
64 bytes from 10.10.10.10: icmp_seq=1 ttl=64 time=0.115 ms
64 bytes from 10.10.10.10: icmp_seq=2 ttl=64 time=0.104 ms
64 bytes from 10.10.10.10: icmp_seq=3 ttl=64 time=0.104 ms
64 bytes from 10.10.10.10: icmp_seq=4 ttl=64 time=0.108 ms
64 bytes from 10.10.10.10: icmp_seq=5 ttl=64 time=0.102 ms
64 bytes from 10.10.10.10: icmp_seq=6 ttl=64 time=0.097 ms
64 bytes from 10.10.10.10: icmp_seq=7 ttl=64 time=0.105 ms
64 bytes from 10.10.10.10: icmp_seq=8 ttl=64 time=0.094 ms
64 bytes from 10.10.10.10: icmp_seq=9 ttl=64 time=0.097 ms
64 bytes from 10.10.10.10: icmp_seq=10 ttl=64 time=0.100 ms
64 bytes from 10.10.10.10: icmp_seq=11 ttl=64 time=0.104 ms
64 bytes from 10.10.10.10: icmp_seq=12 ttl=64 time=0.103 ms
64 bytes from 10.10.10.10: icmp_seq=13 ttl=64 time=0.107 ms
64 bytes from 10.10.10.10: icmp_seq=14 ttl=64 time=0.105 ms
64 bytes from 10.10.10.10: icmp_seq=15 ttl=64 time=0.100 ms
64 bytes from 10.10.10.10: icmp_seq=16 ttl=64 time=0.102 ms
64 bytes from 10.10.10.10: icmp_seq=17 ttl=64 time=0.114 ms
64 bytes from 10.10.10.10: icmp_seq=18 ttl=64 time=0.103 ms
64 bytes from 10.10.10.10: icmp_seq=19 ttl=64 time=0.104 ms
64 bytes from 10.10.10.10: icmp_seq=20 ttl=64 time=0.100 ms
^C
--- 10.10.10.10 ping statistics ---
20 packets transmitted, 20 received, 0% packet loss, time 761ms
rtt min/avg/max/mdev = 0.094/0.103/0.115/0.010 ms
pi@pi4-mate:~ $

Where can I find some gcode test files that have 0,0,0 in left down corner?

How big ?

It is parametric, so change the XY scale to make it bigger or smaller and set the feed rate under #21, press play:

Time for me now to add plasmaC aseverything looks to be working OK.

Need to fix some mechanics, was a bit over optimistic re stepper motor fasteners.
But the concept works that i scrambled together and I am happy about that!

Big thanks to all cheering on my long way here.

Hmmmm
Did run the configurator, obviously with not all correct so I then did run configurator and tried reconfigure = here it stopped. So I can not get my errors correct. Bug?

Make a new config with the configurator and delete the old one.