Hypersense configuration with 2.8 and PlasmaC

rodw
Offline
Platinum Member

5 years 5 months ago #207905 by rodw

Replied by rodw on topic Hypersense configuration with 2.8 and PlasmaC

phillc54 wrote: The same one it has always been, plasmac.ohmic-enable

Thanks

In the connections file
change:

Code:

#net plasmac:ohmic-enable plasmac.ohmic-enable  =>

Code:

#net plasmac:ohmic-enable plasmac.ohmic-enable  => ohmicsense.is-probing

and comment out any other lines that use ohmicsense.is-probing

Please Log in to join the conversation.

txtrone
Topic Author
Offline
Platinum Member

5 years 5 months ago #207908 by txtrone

Replied by txtrone on topic Hypersense configuration with 2.8 and PlasmaC

tommylight wrote: Just to be sure, does the torch have an electrode, a nozzle and a shield ?

Yes sir. Here are some screen shots from several days ago, after I installed the 390k 1W, showing the voltage reading in hal show. One without touching the plate, the other shows the reading while touching the plate.

Attachment not found

Please Log in to join the conversation.

rodw
Offline
Platinum Member

5 years 5 months ago #207912 by rodw

Replied by rodw on topic Hypersense configuration with 2.8 and PlasmaC

Ahh, we did not get it right earlier either. My last post should solve it.

Please Log in to join the conversation.

rodw
Offline
Platinum Member

5 years 5 months ago #207914 by rodw

Replied by rodw on topic Hypersense configuration with 2.8 and PlasmaC

Probably also comment out all of this

Code:

# --- Replace Plasmacâ€™s Ohmic sensing signal ---
unlinkp db_ohmic.in
net ohmic-true ohmicsense.ohmic-on => db_ohmic.in
net plasmac:ohmic-enable    =>  ohmicsense.is-probing

and in Plasma Connections, change

Code:

net plasmac:ohmic-probe hm2_7i76e.0.7i76.0.0.input-20-not => db_ohmic.in

Code:

net plasmac:ohmic-probe ohmicsense.ohmic-on => db_ohmic.in

for some cleaner code

Please Log in to join the conversation.

txtrone
Topic Author
Offline
Platinum Member

5 years 5 months ago #207915 by txtrone

Replied by txtrone on topic Hypersense configuration with 2.8 and PlasmaC

rodw wrote: Ahh, we did not get it right earlier either. My last post should solve it.

How does this look?

Code:

#***** PLASMA CONNECTIONS *****
net plasmac:arc-voltage-in hm2_7i76e.0.encoder.00.velocity => plasmac.arc-voltage-in
net plasmac:arc-ok-in hm2_7i76e.0.7i76.0.0.input-31 => db_arc-ok.in
net plasmac:float-switch hm2_7i76e.0.7i76.0.0.input-21-not => db_float.in
net plasmac:breakaway hm2_7i76e.0.7i76.0.0.input-22-not => db_breakaway.in
net plasmac:ohmic-probe hm2_7i76e.0.7i76.0.0.input-20-not => db_ohmic.in
#net plasmac:ohmic-enable plasmac.ohmic-enable  => ohmicsense.is-probing
net plasmac:torch-on => hm2_7i76e.0.7i76.0.0.spinena

# ---ENCODER SETTINGS---

# --- 7i76e ENCODER SETUP FOR TORCH VOLTAGE ---
setp hm2_7i76e.0.encoder.00.scale -1
setp hm2_7i76e.0.encoder.00.counter-mode 1

# --- Load the Component ---
loadrt ohmic names=ohmicsense
addf ohmicsense servo-thread

# --- 7i76e ENCODER 2 SETUP FOR OHMIC SENSING---
setp hm2_7i76e.0.encoder.01.scale -1
setp hm2_7i76e.0.encoder.01.counter-mode 1
setp hm2_7i76e.0.encoder.01.filter 1

# --- Configure the component ---
setp ohmicsense.thcad-0-volt-freq    135700
setp ohmicsense.thcad-max-volt-freq  966000
setp ohmicsense.thcad-divide         32
setp ohmicsense.thcad-fullscale      5
setp ohmicsense.volt-divider         4.9
setp ohmicsense.ohmic-threshold      22.0
setp ohmicsense.ohmic-low            1.0
net ohmic-vel ohmicsense.velocity-in <= hm2_7i76e.0.encoder.01.velocity


# --- Replace Plasmacâ€™s Ohmic sensing signal ---
unlinkp db_ohmic.in
net ohmic-true ohmicsense.ohmic-on => db_ohmic.in
#net plasmac:ohmic-enable    =>  ohmicsense.is-probing
setp ohmicsense.is-probing 1

Please Log in to join the conversation.

txtrone
Topic Author
Offline
Platinum Member

5 years 5 months ago #207916 by txtrone

Replied by txtrone on topic Hypersense configuration with 2.8 and PlasmaC

rodw wrote: Probably also comment out all of this...

Better? Did I get the line 'setp ohmicsense.is-probing 1' in the correct area?

Code:

#***** PLASMA CONNECTIONS *****
net plasmac:arc-voltage-in hm2_7i76e.0.encoder.00.velocity => plasmac.arc-voltage-in
net plasmac:arc-ok-in hm2_7i76e.0.7i76.0.0.input-31 => db_arc-ok.in
net plasmac:float-switch hm2_7i76e.0.7i76.0.0.input-21-not => db_float.in
net plasmac:breakaway hm2_7i76e.0.7i76.0.0.input-22-not => db_breakaway.in
net plasmac:ohmic-probe ohmicsense.ohmic-on => db_ohmic.in
#net plasmac:ohmic-enable plasmac.ohmic-enable  => ohmicsense.is-probing
net plasmac:torch-on => hm2_7i76e.0.7i76.0.0.spinena

# ---ENCODER SETTINGS---

# --- 7i76e ENCODER SETUP FOR TORCH VOLTAGE ---
setp hm2_7i76e.0.encoder.00.scale -1
setp hm2_7i76e.0.encoder.00.counter-mode 1

# --- Load the Component ---
loadrt ohmic names=ohmicsense
addf ohmicsense servo-thread

# --- 7i76e ENCODER 2 SETUP FOR OHMIC SENSING---
setp hm2_7i76e.0.encoder.01.scale -1
setp hm2_7i76e.0.encoder.01.counter-mode 1
setp hm2_7i76e.0.encoder.01.filter 1

# --- Configure the component ---
setp ohmicsense.thcad-0-volt-freq    135700
setp ohmicsense.thcad-max-volt-freq  966000
setp ohmicsense.thcad-divide         32
setp ohmicsense.thcad-fullscale      5
setp ohmicsense.volt-divider         4.9
setp ohmicsense.ohmic-threshold      22.0
setp ohmicsense.ohmic-low            1.0
net ohmic-vel ohmicsense.velocity-in <= hm2_7i76e.0.encoder.01.velocity
setp ohmicsense.is-probing 1

# --- Replace Plasmacâ€™s Ohmic sensing signal ---
#unlinkp db_ohmic.in
#net ohmic-true ohmicsense.ohmic-on => db_ohmic.in
#net plasmac:ohmic-enable    =>  ohmicsense.is-probing

Please Log in to join the conversation.

txtrone
Topic Author
Offline
Platinum Member

5 years 5 months ago #207960 by txtrone

Replied by txtrone on topic Hypersense configuration with 2.8 and PlasmaC

Got it working, thanks for all the help! Below is my hal connection file.

Attachment not found

Please Log in to join the conversation.

rodw
Offline
Platinum Member

5 years 5 months ago #208003 by rodw

Replied by rodw on topic Hypersense configuration with 2.8 and PlasmaC

Great work!

Please Log in to join the conversation.

txtrone
Topic Author
Offline
Platinum Member

5 years 5 months ago #208011 by txtrone

Replied by txtrone on topic Hypersense configuration with 2.8 and PlasmaC

rodw wrote: Great work!

Thanks Rod, but technically I should be congratulating you and everyone on this forum that helped me get this far! If this forum went bowling, I would be Donny... maybe you would be the Dude... not sure about Walter, though I have my suspicions.

Please Log in to join the conversation.

Time to create page: 0.060 seconds