Probe Basic spindle load bar off by a decimal

TurBoss
Offline
Premium Member

4 years 1 month ago #251441 by TurBoss

Replied by TurBoss on topic Probe Basic spindle load bar off by a decimal

Thanks I edited my post with the correct component names.

Please Log in to join the conversation.

Lcvette
Offline
Platinum Member

4 years 1 month ago #251445 by Lcvette

Replied by Lcvette on topic Probe Basic spindle load bar off by a decimal

Thanks @Turboss and no worries @masterjuggler glad you got it sorted! can you take a small video of it working? i've still yet to set mine up even though i've bought the component that will capture the amperage and output an analog signal.. but you did remind me i had it on a shelf somewhere so i pulled it out and dusted it off so i could start planning its install!

Please Log in to join the conversation.

masterjuggler
Topic Author
Offline
New Member

4 years 1 month ago #251447 by masterjuggler

Replied by masterjuggler on topic Probe Basic spindle load bar off by a decimal

Attached a quick demo of the spindle load bar working if that helps give motivation lol.

By the way, on a totally unrelated note, how are you supposed to configure the pin display on the status page? I see that I can edit each pin's name and the card names, but I haven't been able to find how to either set them up in the gui or add them to a config file.

EDIT: seems I can't upload a proper video, so I zipped it. Oh well.

Please Log in to join the conversation.

Lcvette
Offline
Platinum Member

4 years 1 month ago #251448 by Lcvette

Replied by Lcvette on topic Probe Basic spindle load bar off by a decimal

awesome! how is the updating in realtime? is it pretty smooth?

Please Log in to join the conversation.

masterjuggler
Topic Author
Offline
New Member

4 years 1 month ago #251450 by masterjuggler

Replied by masterjuggler on topic Probe Basic spindle load bar off by a decimal

It seems to be updating in real time, if a bit stuttery. But it's entirely probable that's caused by the fact that I'm running LinuxCNC on an AMD Athlon x2 lol.

Please Log in to join the conversation.

daveyr
Away
Junior Member

4 years 1 week ago #254812 by daveyr

Replied by daveyr on topic Probe Basic spindle load bar off by a decimal

I have been trying to the same as in this thread but i seem to not be able to find halcompile

For my install i used the joco-nz bullseye installer to install the dev version of probe basic and linuxcnc 2.9

I am not sure if you would be willing to share your compiled version as i also have a 9 amp max for my VFD.

Please Log in to join the conversation.

TurBoss
Offline
Premium Member

4 years 1 week ago #254817 by TurBoss

Replied by TurBoss on topic Probe Basic spindle load bar off by a decimal

Hello

To get halcompile you need to install linuxcnc-dev or linuxcnc-uspace-dev

Please Log in to join the conversation.

CNC_ANDI
Offline
Elite Member

3 years 9 months ago #262823 by CNC_ANDI

Replied by CNC_ANDI on topic Probe Basic spindle load bar off by a decimal

at
halcompile --install load_conv.comp

i get this error:

Code:

cnc@debian:~$ halcompile --install load_conv.comp
Traceback (most recent call last):
File "/usr/bin/halcompile", line 1556, in <module>
main()
File "/usr/bin/halcompile", line 1526, in main
process(f, mode, outfile)
File "/usr/bin/halcompile", line 1366, in process
a, b = parse(filename)
File "/usr/bin/halcompile", line 434, in parse
f = open(filename).read()
FileNotFoundError: [Errno 2] No such file or directory: 'load_conv.comp'


where i can find load_conv.comp?

For my install i used the joco-nz bullseye installer to install the dev version of probe basic and linuxcnc 2.9

Please Log in to join the conversation.

TurBoss
Offline
Premium Member

3 years 9 months ago #262825 by TurBoss

Replied by TurBoss on topic Probe Basic spindle load bar off by a decimal

hello

find it here:
forum.linuxcnc.org/media/kunena/attachme...17006/load_conv.comp

Please Log in to join the conversation.

CNC_ANDI
Offline
Elite Member

3 years 9 months ago #262827 by CNC_ANDI

Replied by CNC_ANDI on topic Probe Basic spindle load bar off by a decimal

thanks.

Code:

cnc@debian:~/linuxcnc/configs/CNC-ANDI$ sudo halcompile --install load_conv.comp[sudo] password for cnc: 
Compiling realtime load_conv.c
Linking load_conv.so
cp load_conv.so /usr/lib/linuxcnc/modules/

percent = round(amps/0.12);

is for 12A at 100 or 150%?

Please Log in to join the conversation.

Time to create page: 0.059 seconds