Probe Basic spindle load bar off by a decimal

More
3 years 9 months ago #262883 by Lcvette
Replied by Lcvette on topic Probe Basic spindle load bar off by a decimal
I would set the 100% mark to the spindles 100% duty cycle amperage rating. some spindles have the capability to run at levels up to 150% or more amperage for short periods of time. but either way 100% should be the max continuous amperage rating allowed in the drive/motor manuals

Please Log in to join the conversation.

More
3 years 9 months ago #262890 by CNC_ANDI
Replied by CNC_ANDI on topic Probe Basic spindle load bar off by a decimal
ok thanks, my spindle is 400V 4.5kw 10A

so i set this percent = round(amps/0.10); for 100%

so my VFD has a Digital current output, i will wire this to my mesa 7i76e input.

so find found this hal code

Code:
loadrt load_conv addf load-conv.0 servo-thread # net vfd.Rott => spindle.0.speed-in setp qtpyvcp.spindle-load-indicator.max-val 125 net spindle-current => load-conv.0.amps net spindle-load qtpyvcp.spindle-load-indicator.in-f <= load-conv.0.percent net spindle-current => qtpyvcp.spindle-load-indicator.in-f # net spindle-speed-fb => qtpyvcp.spindle-encoder-rpm.in

so i must set my input pin to spindle-current?
is that right?

Please Log in to join the conversation.

More
3 years 1 month ago #280661 by CNC_ANDI
Replied by CNC_ANDI on topic Probe Basic spindle load bar off by a decimal
Yesterday i got a working Spindleloadbar on Probe basic with the VFDMod at my DZB VFD

I´m Happy. Thanks.

Please Log in to join the conversation.

More
2 years 9 months ago #290498 by warwickben
Replied by warwickben on topic Probe Basic spindle load bar off by a decimal
I’m trying to wrap my head around this . 
I installed Linuxcnc from the main iso for 2.9.2 ,    Is that upspxe -dev?
Do I have todo any thing to my install to use load_conv.comp.  Can I just install what’s needed ?
Sorta don’t want to have to start over just for spindle load gauge since the only other thing I need todo for my machine is m6 remap.

 

Please Log in to join the conversation.

More
2 years 9 months ago #290588 by daveyr
Replied by daveyr on topic Probe Basic spindle load bar off by a decimal
I just re-installed this morning from the new 2.9.2 iso and was able to do
Code:
sudo halcompile --install load_conv.comp

from the folder that i had the load_conv.comp in (In my case my config folder) and it worked nothing else was needed.
 

Please Log in to join the conversation.

More
2 years 5 months ago #301479 by COFHAL
Replied by COFHAL on topic Probe Basic spindle load bar off by a decimal
Could you share how I achieved it?

Please Log in to join the conversation.

More
2 years 5 months ago #301488 by COFHAL
Replied by COFHAL on topic Probe Basic spindle load bar off by a decimal
Could you share how I achieved it?

Please Log in to join the conversation.

More
2 years 5 months ago #301662 by CNC_ANDI
Replied by CNC_ANDI on topic Probe Basic spindle load bar off by a decimal
you have to do install the load_conv with
sudo halcompile --install load_conv.comp

and then you have to edit and paste that in your hal
loadrt load_conv

addf load-conv.0 servo-thread

setp qtpyvcp.spindle-load-indicator.max-val 100
net spindle-current => load-conv.0.amps
net spindle-load qtpyvcp.spindle-load-indicator.in-f <= load-conv.0.percent

Please Log in to join the conversation.

More
2 years 5 months ago #301677 by COFHAL
Replied by COFHAL on topic Probe Basic spindle load bar off by a decimal
Thanks for your reply. I understand that, what I don't know is where you get that spindle load value from, do you get it through MODBUS or through the analog output of the VFD?

Please Log in to join the conversation.

More
2 years 5 months ago #301696 by CNC_ANDI
Replied by CNC_ANDI on topic Probe Basic spindle load bar off by a decimal
mine comes from modbus

Please Log in to join the conversation.

Time to create page: 0.093 seconds
Powered by Kunena Forum