It's the IDs that are the issue which are hard coded into the driver. 2.9.7 won't help.

Try the wheezy ISO from the downloads page, tho it will limit the version of Linuxcnc you can use. That really isn't an issue as it will work fine. Actually there's a few members that run earlier versions.

I personally think that modern Operating systems need more than 2 cores to  run  Linuxcnc these days. Give RTAI for 2.94 a go and see how you go.
I have no experience.

Thanks I’ll be sure to check this.

Linuxcnc 2.9.4 was released to fix some things with with XHC USB pendants. Perhaps an upgrade will fix things. Here is how to get it on Trixie
 

There may be more than the usb product code that differ between them.
Here is where to change  github.com/LinuxCNC/linuxcnc/blob/fb1480...-whb04b-6/usb.h#L311
Then build linuxcnc and run-in-place.

Mesa just shipped product to Welectron  and Eusurplus

In addition Eusurplus has 7I97Ts in stock

No LSB modules are available
Distributior ID: Debian
Codename: bookworm

2. When the clamps are release and the scale is plugged in and the NC- ready is on its almost as if the mesa card sends out a voltage causing the motor to “bump” which causes a joint error. If I unplug the scale and still leave the clamps off the machine runs fine and the table is steady doesn’t drift. 

If this is a analog system and you prevent motion, Normally you would need to disable the PID
feedback when locked (especially if there is any I term)  Otherwise a large output can develop
as the PID "fights" against the apparent resistance to motion.

Thanks
Pico is on my watchlist.
Unfortunately they do seem to have any dealers in EU.

Gib mal im Terminal ein: lsb_release -ic
Was wird ausgegeben?

Thanks
Problem is availability
Welectron do not sell mesa products any longer
Eusurplus is very limited in stock so I fear they are tapping out of mesa as well.
If it’s not sold within EU we cannot use them as suppliers

Hi all. I’ve converted my maho 700 over to Linuxcnc using a lot of information from Mark (rotary smp). I need some advice or guidance.  So all 3 axis are working and I’ve managed to figure out and get the PID tuning running smoothly. At 1000/mm.s 
im struggling with the A axis which uses a Heidenheim scale. 
1. What scale settings do I give it or how do I workout the scale value of the a axis. 
2. When the clamps are release and the scale is plugged in and the NC- ready is on its almost as if the mesa card sends out a voltage causing the motor to “bump” which causes a joint error. If I unplug the scale and still leave the clamps off the machine runs fine and the table is steady doesn’t drift. 

3. What or how can I get the spindle to be steady? Again of the plug is unplugged from the mesa card the spindle doesn’t “spin” but when plugged in it moves slowly like maybe .5 of a rpm sort of a drift. 

4. Are you somehow feeding a Tacho signal to the mesa card so it can control RPM? Or are you just basing it off the calculation? And how do you get more range so I can run it from 0-6000 rpm. 

5. Might be a silly question this is really a hobby for me. But what is a max MM/S for these machines? Trying to get the max set but don’t want to cause any damage. 


I haven’t worked on the gearbox settings yet just want to figure out the axis first. 

Regards 
Sven 
 

Moin an alle

Ich habe soeben meinen Rechner gestartet und alle Symbole auf dem Desktop sind verschwunden. Ich kann auch keine neuen Verknüpfungen platzieren und die rechte Maustaste reagiert ebenfalls nicht. 
Auf jeder anderen Stelle öffnet sich das RMB Menü.

Was ist hier passiert? Kennt jemand das Problem?
Ich habe Linuxcnc 2.9.2 installiert 

Hi,

I have an old computer (pre 2010), 2G ram.  LinuxCNC 2.9.4 runs on it, but I cannot get the jitter down. I have tried a lot of suggestions on this forum (bios settings, deactivating unused hardware etc.). I think the preempt-rt kernel would not work with this computer.

I want to use it for a 4 axis wood router, no fancy peripherals (keyboard and mouse control). What RTAI version of LinuxCNC is lightweight and still has a user friendly interface. I have not tried any of them, I want to ask here first.

Thanks