1. LinuxCNC
  3. General LinuxCNC Questions
  5. Connections probles

Connections probles

More
22 Oct 2023 16:41 #283509 by alfredmaina
Connections probles was created by alfredmaina
HI all...I have a problem with  my linux CNC connection to my mesa 7i96 board.
i have configured board to IP 10.10.10.10 and my jumper set to W5 DOWN and W6 up but after trying to open my shortcut the attached is what is displayed with a connection error.
Kindly assist.
 

Please Log in or Create an account to join the conversation.

  • tommylight
  • tommylight's Avatar
  • Away
  • Moderator
  • Moderator
More
22 Oct 2023 16:50 #283512 by tommylight
Replied by tommylight on topic Connections probles
No attachment.

Please Log in or Create an account to join the conversation.

More
22 Oct 2023 18:02 #283521 by alfredmaina
Replied by alfredmaina on topic Connections probles
Sorry....these attached displays are what i get after i try to open.     
Attachments:

Please Log in or Create an account to join the conversation.

  • tommylight
  • tommylight's Avatar
  • Away
  • Moderator
  • Moderator
More
23 Oct 2023 00:24 #283548 by tommylight
Replied by tommylight on topic Connections probles
First and foremost, why are you using CraftsmanCNC configuration? A few years back it was unusable without a lot of editing as it had hard coded file paths.
You have set the Mesa card as you say, but you have not set the PC network for use with mesa, see here:
forum.linuxcnc.org/27-driver-boards/3559...ethernet-mesa-boards

Please Log in or Create an account to join the conversation.

More
23 Oct 2023 07:36 #283580 by alfredmaina
Replied by alfredmaina on topic Connections probles
CraftsmanCNC is the name i have given to my pncconfig.

Thank you Tommy. i will try this and give you an update as soon.
The following user(s) said Thank You: tommylight

Please Log in or Create an account to join the conversation.

  • tommylight
  • tommylight's Avatar
  • Away
  • Moderator
  • Moderator
More
23 Oct 2023 16:17 #283614 by tommylight
Replied by tommylight on topic Connections probles

CraftsmanCNC is the name i have given to my pncconfig.

The same one that was on cnczone forums? :)

Please Log in or Create an account to join the conversation.

More
24 Oct 2023 07:48 #283677 by alfredmaina
Replied by alfredmaina on topic Connections probles
A funny coincidence i think. my workshop is called that.

Please Log in or Create an account to join the conversation.

More
24 Oct 2023 08:04 #283678 by alfredmaina
Replied by alfredmaina on topic Connections probles
Hi Tommy. I tried to edit connections but nothing could display. Is there something that i might have missed during the installation? Sorry am new to linux.. 
Attachments:

Please Log in or Create an account to join the conversation.

More
24 Oct 2023 09:18 #283684 by JPL
Replied by JPL on topic Connections probles
Oh! So many icons... You have another common problem there. Read this to first solve this issue: forum.linuxcnc.org/38-general-linuxcnc-q...little-issues#226480

Did you follow the instruction here to setup your network: forum.linuxcnc.org/27-driver-boards/3559...ethernet-mesa-boards

Or did you edit the file /etc/network/interfaces as explained here: linuxcnc.org/docs/2.9/html/man/man9/hm2_eth.9.html

(Both ways are ok but you can use only one of the two)
The following user(s) said Thank You: tommylight

Please Log in or Create an account to join the conversation.

More
24 Oct 2023 12:24 #283695 by alfredmaina
Replied by alfredmaina on topic Connections probles
1. I have tried to remove the many icons popping up but see the attached on what am getting on the sudo.
2.Previoussly I tried to follow the instructions to set up my network but the "edit connections" option could activate.   
Attachments:

Please Log in or Create an account to join the conversation.

  1. LinuxCNC
  3. General LinuxCNC Questions
  5. Connections probles
Time to create page: 0.151 seconds
Powered by Kunena Forum