General LinuxCNC Questions (2236 topics)

Questions about LinuxCNC

Subject	Replies / Views	Last Post
Other Sources for Information about LinuxCNC Topic started 08 Jan 2013 02:16, by BigJohnT Locked Last Post 08 Jan 2013 02:16 by BigJohnT Locked	Replies:0 Views:6732	Last Post by BigJohnT 08 Jan 2013 02:16
FAQ Topic started 17 Feb 2010 13:25, by BigJohnT Locked Last Post 17 Feb 2010 13:25 by BigJohnT Locked	Replies:0 Views:12.7k	Last Post by BigJohnT 17 Feb 2010 13:25

smartprobe - configuration questions Topic started 10 Jun 2016 17:20, by joe Last Post 22 Jul 2017 01:40 by choppero 1 2 3	Replies:20 Views:1188	Last Post by choppero 22 Jul 2017 01:40
A few questions on machine build MX4660, 7i92M, and Intel Celeron NUC type PC Topic started 11 Jul 2017 15:52, by photomankc Last Post 21 Jul 2017 00:30 by photomankc	Replies:6 Views:109	Last Post by photomankc 21 Jul 2017 00:30
servo PID tuning Topic started 02 May 2017 11:51, by BramVH Last Post 20 Jul 2017 14:15 by Todd Zuercher 1 2	Replies:12 Views:235	Last Post by Todd Zuercher 20 Jul 2017 14:15
Backlash - weird issue Topic started 19 Jul 2017 12:12, by GarthN Last Post 20 Jul 2017 12:48 by Todd Zuercher	Replies:7 Views:80	Last Post by Todd Zuercher 20 Jul 2017 12:48
PWM generator does not start until the second run Topic started 19 Jul 2017 00:20, by TwoFeetDown Last Post 19 Jul 2017 19:47 by TwoFeetDown	Replies:2 Views:59	Last Post by TwoFeetDown 19 Jul 2017 19:47
Setting initval of a spinbox in hal Topic started 21 Apr 2013 19:43, by mariusl Last Post 19 Jul 2017 17:09 by andypugh 1 2 3 ... 5	Replies:40 Views:8193	Last Post by andypugh 19 Jul 2017 17:09
Using LinuxCNC to control 3 stepper motors concurrently Topic started 17 Jul 2017 07:18, by MattMethods Last Post 19 Jul 2017 08:50 by andypugh	Replies:5 Views:106	Last Post by andypugh 19 Jul 2017 08:50
Incorrect Axis Motion Topic started 17 Jul 2017 08:19, by sanmd Last Post 19 Jul 2017 00:13 by PCW 1 2	Replies:11 Views:141	Last Post by PCW 19 Jul 2017 00:13
Gantry Homing Topic started 05 Jun 2017 23:16, by e76nystrom Last Post 18 Jul 2017 19:11 by Yannis	Replies:4 Views:166	Last Post by Yannis 18 Jul 2017 19:11
mesa 5i25 and mx4660 installation and configuration Topic started 27 May 2017 06:49, by goofy Last Post 18 Jul 2017 16:25 by goofy 1 2 3 4	Replies:30 Views:563	Last Post by goofy 18 Jul 2017 16:25
Poblems configuring Parallel Port Pin 1,14,16 and Topic started 19 Mar 2016 22:48, by gadget Last Post 18 Jul 2017 11:53 by andypugh	Replies:5 Views:440	Last Post by andypugh 18 Jul 2017 11:53
DMESG report help Topic started 12 Jul 2017 00:51, by stevclarknz Last Post 18 Jul 2017 11:50 by andypugh	Replies:9 Views:128	Last Post by andypugh 18 Jul 2017 11:50
Retrofit a solder robot? Topic started 16 Jul 2017 13:25, by yello Last Post 18 Jul 2017 11:39 by andypugh	Replies:3 Views:85	Last Post by andypugh 18 Jul 2017 11:39
Which THC card for powermax 45 Topic started 23 May 2016 15:27, by cruzinone Last Post 18 Jul 2017 04:18 by cruzinone 1 2 3	Replies:21 Views:938	Last Post by cruzinone 18 Jul 2017 04:18
PID SERVO TUNING Topic started 11 Jul 2017 05:14, by Yannis Last Post 17 Jul 2017 18:02 by Yannis 1 2 3 4	Replies:32 Views:342	Last Post by Yannis 17 Jul 2017 18:02
My machine is to slow. Topic started 15 Jul 2017 19:43, by Sergio Last Post 17 Jul 2017 10:09 by Sergio	Replies:3 Views:105	Last Post by Sergio 17 Jul 2017 10:09
Lost newbie needs help Topic started 11 Jul 2017 02:12, by stevclarknz Last Post 12 Jul 2017 23:11 by cncnoob1979	Replies:7 Views:134	Last Post by cncnoob1979 12 Jul 2017 23:11
Emco 240 Tool Turret Topic started 03 Jul 2017 16:47, by timmert Last Post 12 Jul 2017 12:42 by andypugh 1 2 3	Replies:27 Views:505	Last Post by andypugh 12 Jul 2017 12:42

Time to create page: 0.310 seconds