LinuxCNC error
- tda2261
- Offline
- New Member
-
Less
More
- Posts: 10
- Thank you received: 0
31 Oct 2023 20:18 #284208
by tda2261
LinuxCNC error was created by tda2261
I am getting an error code when loading up LinuxCNC. I have the mesa boards installed. Error code: ' /usr/realtime-3.4.55-rtai-2/modules/linuxcnc/hm2_7i43.ko' : -1 Input/output error. could someone help me troubleshoot the error?
Please Log in or Create an account to join the conversation.
- tda2261
- Offline
- New Member
-
Less
More
- Posts: 10
- Thank you received: 0
31 Oct 2023 20:19 - 31 Oct 2023 20:22 #284210
by tda2261
Replied by tda2261 on topic LinuxCNC error
let me know if you need any images
Last edit: 31 Oct 2023 20:22 by tda2261.
Please Log in or Create an account to join the conversation.
- tommylight
-
- Away
- Moderator
-
Less
More
- Posts: 19764
- Thank you received: 6681
31 Oct 2023 20:33 #284213
by tommylight
Replied by tommylight on topic LinuxCNC error
Error report, especially the debug part.
Please Log in or Create an account to join the conversation.
- tda2261
- Offline
- New Member
-
Less
More
- Posts: 10
- Thank you received: 0
01 Nov 2023 11:30 #284246
by tda2261
Replied by tda2261 on topic LinuxCNC error
Debug information:
Last couple of lines:
Last couple of lines:
Attachments:
Please Log in or Create an account to join the conversation.
- tommylight
-
- Away
- Moderator
-
Less
More
- Posts: 19764
- Thank you received: 6681
01 Nov 2023 12:47 #284250
by tommylight
Replied by tommylight on topic LinuxCNC error
Moved to "driver boards".
Please Log in or Create an account to join the conversation.
- PCW
-
- Offline
- Moderator
-
Less
More
- Posts: 18220
- Thank you received: 4942
01 Nov 2023 13:59 #284258
by PCW
Replied by PCW on topic LinuxCNC error
LinuxCNC did not find the 7I43 card.
some possible causes are:
7I43 not in EPP mode (7I43 jumper setting)
No 5V power to 7I43
Bad 7I43
Bad parallel cable or 7I43 not connected
Parallel port not in EPP 1.9 mode (BIOS setting)
Bad parallel port
some possible causes are:
7I43 not in EPP mode (7I43 jumper setting)
No 5V power to 7I43
Bad 7I43
Bad parallel cable or 7I43 not connected
Parallel port not in EPP 1.9 mode (BIOS setting)
Bad parallel port
Please Log in or Create an account to join the conversation.
- tda2261
- Offline
- New Member
-
Less
More
- Posts: 10
- Thank you received: 0
02 Nov 2023 13:59 #284328
by tda2261
Replied by tda2261 on topic LinuxCNC error
How do I check or change it into EPP mode?
Please Log in or Create an account to join the conversation.
- PCW
-
- Offline
- Moderator
-
Less
More
- Posts: 18220
- Thank you received: 4942
02 Nov 2023 14:16 #284330
by PCW
On the BIOS it depends but there is usually an I/O setup section
and you can select the parallel port address and operational mode.
Is the 7I43 connected to a motherboard parallel port connector?
Replied by PCW on topic LinuxCNC error
On the 7I43, W4 and W5 down,How do I check or change it into EPP mode?
On the BIOS it depends but there is usually an I/O setup section
and you can select the parallel port address and operational mode.
Is the 7I43 connected to a motherboard parallel port connector?
Please Log in or Create an account to join the conversation.
- tda2261
- Offline
- New Member
-
Less
More
- Posts: 10
- Thank you received: 0
02 Nov 2023 15:13 #284337
by tda2261
Replied by tda2261 on topic LinuxCNC error
I found that it was in ECP mode in BIOS. I changed it EPP.
The board looks correct, do i need to change anything?
The board looks correct, do i need to change anything?
Please Log in or Create an account to join the conversation.
- tda2261
- Offline
- New Member
-
Less
More
- Posts: 10
- Thank you received: 0
02 Nov 2023 15:41 #284340
by tda2261
Replied by tda2261 on topic LinuxCNC error
i am still getting an error after
Please Log in or Create an account to join the conversation.
Moderators: PCW, jmelson
Time to create page: 0.104 seconds