-
LinuxCNC
-
Installing LinuxCNC
-
(superseeded) Linuxcnc on Linux Mint 19.3 quick and easy installation
(superseeded) Linuxcnc on Linux Mint 19.3 quick and easy installation
Less
More
-
Posts: 19198
-
Thank you received: 6436
-
-
26 Jul 2020 09:01 #175870
by tommylight
We had some storms roll through and lost power. I'll try probably tomorrow when we have power again. Thanks.
Are you in Kosovo ? We had hail storms yesterday, the roads were full of water that driving at 20 KMH was hard !
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 401
-
Thank you received: 168
-
-
26 Jul 2020 15:12 #175909
by dvn4life1972
Ok now I tried cntrl+shift 3 times on reboot and it doesn't go to grub at all. It just boots into the desktop as normal.
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 401
-
Thank you received: 168
-
-
26 Jul 2020 15:23 #175911
by dvn4life1972
We had some storms roll through and lost power. I'll try probably tomorrow when we have power again. Thanks.
Are you in Kosovo ? We had hail storms yesterday, the roads were full of water that driving at 20 KMH was hard !
I'm in the US, in Texas. There was a hurricane coming inland about 3 hours to the south, pushing some storms up here where I'm at.
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 19198
-
Thank you received: 6436
-
-
26 Jul 2020 15:58 #175917
by tommylight
Ok now I tried cntrl+shift 3 times on reboot and it doesn't go to grub at all. It just boots into the desktop as normal.
Did you try both sides of the keyboard ? I have two PCS that require that on a USB keyboard.
so both CTRL and both Shifts
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 401
-
Thank you received: 168
-
-
26 Jul 2020 16:07 #175920
by dvn4life1972
Ok now I tried cntrl+shift 3 times on reboot and it doesn't go to grub at all. It just boots into the desktop as normal.
Did you try both sides of the keyboard ? I have two PCS that require that on a USB keyboard.
so both CTRL and both Shifts
Just tried it twice, then a 3rd with the wireless keyboard removed and an old-school good wired keyboard instead. Just boots normal into the Mint desktop.
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 19198
-
Thank you received: 6436
-
-
26 Jul 2020 17:37 #175932
by tommylight
sudo add-apt-repository ppa:danielrichter2007/grub-customizer
sudo apt-get update
sudo apt-get install grub-customizer
Go to Menu > Administration > Grub Customizer > select the kernel with RT in the name > click the up arrow untill that is the top most choice > Save and close, reboot.
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 401
-
Thank you received: 168
-
-
26 Jul 2020 19:35 #175956
by dvn4life1972
sudo add-apt-repository ppa:danielrichter2007/grub-customizer
sudo apt-get update
sudo apt-get install grub-customizer
Did that. The only option with RT was recovery mode, booted to that and ran uname -a and its RT but only in recovery mode.
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 401
-
Thank you received: 168
-
-
26 Jul 2020 20:06 #175960
by dvn4life1972
Went back to the Grub thing again and this time the non-recovery one was there. Moved it to the top and rebooted, and now after uname -a it's showing RT. Thanks Tommy.
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 401
-
Thank you received: 168
-
-
Less
More
-
Posts: 19198
-
Thank you received: 6436
-
-
26 Jul 2020 21:01 #175973
by tommylight
Nevermind that, make the config and save it, you can tune things later from LinuxCNC using the calibration thingy.
What does uname -a say now ?
Please Log in or Create an account to join the conversation.
-
LinuxCNC
-
Installing LinuxCNC
-
(superseeded) Linuxcnc on Linux Mint 19.3 quick and easy installation
Time to create page: 0.113 seconds
