gmoccapy 2.1.0 has been released
03 Aug 2016 18:43 - 03 Aug 2016 18:47 #78335
by newbynobi
gmoccapy 2.1.0 has been released was created by newbynobi
Hallo,
I released gmoccapy 2.1.0
What is new?
You may take a look on YouTube
Norbert waiting for your comments
I released gmoccapy 2.1.0
What is new?
- gmoccapy does support the new master branch, supporting Joint Axis mode
- It does support 5 axis
- it supports 8 joints
- The program name moved to the preview, leaving more space in the info tab
- New touchscreen controls, replacing the previous used sliders
- Unfortunately renaming of hal pin to group them, so be aware that you will have to change hal files
You may take a look on YouTube
Norbert waiting for your comments
Please Log in or Create an account to join the conversation.
03 Aug 2016 20:25 #78338
by tommylight
Replied by tommylight on topic gmoccapy 2.1.0 has been released
From a glimpse .......much better !!! 
I use mostly FHD monitors, so using Gmoccapy was not on the list, but i do like it very much on low resolution screens.
I never had the time to fiddle with it to make things i need bigger, as i use a lot of plasma cutters, and that was for me unusable.
Will give it a try for sure ( i always do ), and report back.
Danke schon, Norbert
MFG
Tom
I use mostly FHD monitors, so using Gmoccapy was not on the list, but i do like it very much on low resolution screens.
I never had the time to fiddle with it to make things i need bigger, as i use a lot of plasma cutters, and that was for me unusable.
Will give it a try for sure ( i always do ), and report back.
Danke schon, Norbert
MFG
Tom
Please Log in or Create an account to join the conversation.
04 Aug 2016 05:47 - 04 Aug 2016 05:49 #78344
by newbynobi
Replied by newbynobi on topic gmoccapy 2.1.0 has been released
Thanks Tom,
gmoccapy runs fine on Full HD, (1920 x 1080), at least here
I unfortunately do not have a TouchScreen with that resolution, my touch has SXGA (1280 x 1024) and I made all controls to be used with the finger on that resolution. Most users seem to use still a mouse
What Gui do you use at the moment?
Do you know gmoccapy_plasma? A screen supported from Marius special made for plasma cutter. It is original gmoccapy with Emmbeded Tabs on nearly all posible places!
If you make a draft of the screen you need, I could look if it possible to realize. Just changing the size of the controls is easy and can be done in very short time. It is just editing the glade file and replace the existing one.
So waiting for your screen design sketch
Norbert
gmoccapy runs fine on Full HD, (1920 x 1080), at least here
I unfortunately do not have a TouchScreen with that resolution, my touch has SXGA (1280 x 1024) and I made all controls to be used with the finger on that resolution. Most users seem to use still a mouse
What Gui do you use at the moment?Do you know gmoccapy_plasma? A screen supported from Marius special made for plasma cutter. It is original gmoccapy with Emmbeded Tabs on nearly all posible places!
If you make a draft of the screen you need, I could look if it possible to realize. Just changing the size of the controls is easy and can be done in very short time. It is just editing the glade file and replace the existing one.
So waiting for your screen design sketch
Norbert
Please Log in or Create an account to join the conversation.
09 Aug 2016 20:14 #78540
by newbynobi
Replied by newbynobi on topic gmoccapy 2.1.0 has been released
Hallo Ruben,
A question is neve rstupid, only persons not willing to answer
It is included in master, so get it through git or buildbot.
If you need help, we are here!
Norbert
A question is neve rstupid, only persons not willing to answer
It is included in master, so get it through git or buildbot.
If you need help, we are here!
Norbert
Please Log in or Create an account to join the conversation.
Moderators: newbynobi, HansU
Time to create page: 0.174 seconds