switching from axis to gmoccapy
- ericg
- Offline
- Premium Member
Less
More
- Posts: 147
- Thank you received: 10
30 Jul 2020 06:21 #176479
by ericg
Replied by ericg on topic switching from axis to gmoccapy
thanks Rodw, I'm getting there, just ran a programOk, but like axis, my spindle speed control is still out of whack .
Thanks for your assistance
Thanks for your assistance
The following user(s) said Thank You: rodw
Please Log in or Create an account to join the conversation.
- Mike_Eitel
- Offline
- Platinum Member
Less
More
- Posts: 1150
- Thank you received: 184
01 Aug 2020 07:40 #176757
by Mike_Eitel
Replied by Mike_Eitel on topic switching from axis to gmoccapy
Please Log in or Create an account to join the conversation.
- ericg
- Offline
- Premium Member
Less
More
- Posts: 147
- Thank you received: 10
01 Aug 2020 08:53 #176761
by ericg
Replied by ericg on topic switching from axis to gmoccapy
No, but I will, thank you
Please Log in or Create an account to join the conversation.
- newbynobi
- Offline
- Moderator
Less
More
- Posts: 2075
- Thank you received: 406
11 Aug 2020 05:29 #177860
by newbynobi
Replied by newbynobi on topic switching from axis to gmoccapy
Many buttons are only activated in homed situation.
Have you homed the machine?
Did you watch the video getting started gmoccapy?
You can include your own glade panel and just replace the old vcp panel.
Norbert
Have you homed the machine?
Did you watch the video getting started gmoccapy?
You can include your own glade panel and just replace the old vcp panel.
Norbert
Please Log in or Create an account to join the conversation.
- ericg
- Offline
- Premium Member
Less
More
- Posts: 147
- Thank you received: 10
11 Aug 2020 07:17 #177868
by ericg
Replied by ericg on topic switching from axis to gmoccapy
Thanks for the reply, no I have not seen any video with that title but I have seen a couple of other early basic ones, and I notice that the video showed sliding bars which did not show on my version, because of that and I don't have a touch screen I have gone back to axis.
But would like to give it another go but I would need sliding controls instead of clicking on + or - which is slow, so where would I find that version?
Eric
But would like to give it another go but I would need sliding controls instead of clicking on + or - which is slow, so where would I find that version?
Eric
Please Log in or Create an account to join the conversation.
- newbynobi
- Offline
- Moderator
Less
More
- Posts: 2075
- Thank you received: 406
11 Aug 2020 20:57 #177946
by newbynobi
Replied by newbynobi on topic switching from axis to gmoccapy
That versions of sliders are not in any supported release any more. You can change the steps of the slider buttons, so one klick will not increase by 1 %, but at 5% or what ever you configure.
I got the wish of sliding the controls from different users, so it might be time to think about changing them?
I got the wish of sliding the controls from different users, so it might be time to think about changing them?
Please Log in or Create an account to join the conversation.
- depronman
- Offline
- Senior Member
Less
More
- Posts: 45
- Thank you received: 5
20 Sep 2020 21:20 #182967
by depronman
Replied by depronman on topic switching from axis to gmoccapy
I also would like the sliding buttons, but as its not available could you please explaing more about how to configure the button step from 1% to 5%, this would make the current buttons so much more usable
Best regards, Paul
Best regards, Paul
Please Log in or Create an account to join the conversation.
Moderators: newbynobi, HansU
Time to create page: 0.076 seconds