Axis Position Logger

More
2 years 8 months ago #294417 by Mecanix
Replied by Mecanix on topic Axis Position Logger
Pythonish3 attached. Works great. Although my devbox is GTK3&4 here... might need those two for the ui to load up.

Code:
$ sudo apt install libgtk-3-0 libgtk-3-dev

[img

Please Log in to join the conversation.

More
2 years 8 months ago #294424 by Ehsan_R
Replied by Ehsan_R on topic Axis Position Logger
Code:
ehsan@debian:~/Desktop$ python3 emclog.py   File "/home/ehsan/Desktop/emclog.py", line 193     if moveType in :                    ^ SyntaxError: invalid syntax

Please Log in to join the conversation.

More
2 years 8 months ago #294425 by Aciera
Replied by Aciera on topic Axis Position Logger
Not sure why that got lost, should be:

Code:
if moveType in ['G1', 'G2', 'G3']


[edit]
seems the editor doesn't like the square brackets.

Please Log in to join the conversation.

More
2 years 8 months ago #294426 by Ehsan_R
Replied by Ehsan_R on topic Axis Position Logger
Thanks a lot it works

Please Log in to join the conversation.

More
2 years 8 months ago #294428 by Ehsan_R
Replied by Ehsan_R on topic Axis Position Logger
How can I create a button in the graphical interface of AXIS to run the program by pressing it?
Or add it as a tab to the GUI

Please Log in to join the conversation.

More
2 years 8 months ago #294441 by tommylight
Replied by tommylight on topic Axis Position Logger
Probably using VCP panels
linuxcnc.org/docs/html/gui/pyvcp.html

Please Log in to join the conversation.

More
2 years 8 months ago #294471 by Mecanix
Replied by Mecanix on topic Axis Position Logger
Aren't those GTK ui Axis Tabs friendly? I could be wrong, and much like Tommy recommended (pyvcp), I think you can also have it all running from inside linuxcnc e.g AXISTAB: [Preview] | [DRO] | [EMCLOG]

Search for GladeVCP if interested in learning new tricks. Something like below, not far off anyway...

INI file
Code:
[DISPLAY] EMBED_TAB_NAME = EMCLOG MBED_TAB_LOCATION = ntb_user_tabs1 EMBED_TAB_COMMAND = halcmd loadusr -Wn gladevcp gladevcp -c gladevcp -x {XID} -u ./emclog/emclog.py ./emclog/emclog.ui

Please Log in to join the conversation.

More
2 years 8 months ago #294476 by phillc54
Replied by phillc54 on topic Axis Position Logger
Another option:
linuxcnc.org/docs/2.9/html/gui/axis.html...tton_to_manual_frame
 

Please Log in to join the conversation.

More
2 years 8 months ago #294497 by Aciera
Replied by Aciera on topic Axis Position Logger
The logger ui uses pyqt not gtk (ie it's not a glade panel).

Please Log in to join the conversation.

More
2 years 8 months ago #294514 by Aciera
Replied by Aciera on topic Axis Position Logger
You can execute a python script using a custom M-code:
1. I have the folders 'libemclog' and 'mcodes' in my config folder
2. the [RS274NGC] section of the ini file must contain the path to the 'mcodes' folder:
Code:
USER_M_PATH = ./mcodes

3. Executing 'm129' opens the loggerui window.


 

Attachment not found



I have modified emclog.py so the file handling (Open, Save, SaveAs) is a bit more user friendly.
Note: I'm on a rip installation so I'm not sure the paths are correct for a deb install.

Please Log in to join the conversation.

Time to create page: 0.160 seconds
Powered by Kunena Forum