Reverse run not working in linuxcnc-plasmac github

More
7 years 4 months ago #135615 by phillc54
Replied by phillc54 on topic Reverse run not working in linuxcnc-plasmac github

Is there any way i can make reverse run work...???

It works for me in Wheezy, Stretch and LMDE2 for both Axis and Gmoccapy.

Cheers, Phill.

Please Log in to join the conversation.

More
7 years 4 months ago #135619 by pl7i92
Replied by pl7i92 on topic Reverse run not working in linuxcnc-plasmac github
phil is it in your git reprosity
github.com/phillc54/linuxcnc/

Please Log in to join the conversation.

More
7 years 4 months ago #135623 by phillc54
Replied by phillc54 on topic Reverse run not working in linuxcnc-plasmac github
Reverse run is here: github.com/phillc54/linuxcnc/tree/reverse-run

Plasmac is here: github.com/phillc54/linuxcnc-plasmac or github.com/phillc54/linuxcnc/tree/plasmac

Cheers, Phill.

Please Log in to join the conversation.

More
7 years 4 months ago #135649 by pl7i92
Replied by pl7i92 on topic Reverse run not working in linuxcnc-plasmac github
so its not inside plasmac
only stand alone

Please Log in to join the conversation.

More
7 years 4 months ago #135672 by phillc54
Replied by phillc54 on topic Reverse run not working in linuxcnc-plasmac github
Yes, it is not part of plasmac, although it is used by plasmac.

Cheers, Phill.

Please Log in to join the conversation.

More
7 years 4 months ago #135715 by phoenix
Replied by phoenix on topic Reverse run not working in linuxcnc-plasmac github
sir it seems that paused motion function is not working or I DIIDNT KNOW HOW TO USE IT PROPERLY \
in both cases what can i do to solve this ???

Please Log in to join the conversation.

More
7 years 4 months ago #135729 by phillc54
Replied by phillc54 on topic Reverse run not working in linuxcnc-plasmac github

Bhushan wrote: sir it seems that paused motion function is not working or I DIIDNT KNOW HOW TO USE IT PROPERLY \
in both cases what can i do to solve this ???

It is not helping that you have the same query going on in three different threads.

You haven't answered my question here

I will try to help you on the above thread when you provide an answer.

Cheers, Phill.

Please Log in to join the conversation.

More
7 years 4 months ago #136310 by andypugh
Replied by andypugh on topic Reverse run not working in linuxcnc-plasmac github
I just merged Phill's reverse run branch in to master / 2.9

Bhushan: You have to enable adaptive feed (M52) for adaptive feed (including reverse run) to work. Did you do that?

Please Log in to join the conversation.

More
7 years 4 months ago #136317 by tommylight
Replied by tommylight on topic Reverse run not working in linuxcnc-plasmac github
Fireworks anyone ??? :)

Please Log in to join the conversation.

More
7 years 4 months ago #136323 by rodw
Replied by rodw on topic Reverse run not working in linuxcnc-plasmac github

tommylight wrote: Fireworks anyone ??? :)


Congratulations to Phill for all the hard work and thanks to Andy for getting this into master branch.

Andy, thanks for the heads up about M52, probably explains why I could not work out how this works....

Please Log in to join the conversation.

Time to create page: 0.053 seconds
Powered by Kunena Forum