Problem parralel Port is not reconized in stretch configuration

More
7 years 5 months ago #135301 by Philippe
Replied by Philippe on topic Problem parralel Port is not reconized in stretch configuration
i don't saw the address parallel port in the ini or hal file, but with the last version weehzy all was OK

Please Log in to join the conversation.

More
7 years 5 months ago #135307 by Todd Zuercher
Replied by Todd Zuercher on topic Problem parralel Port is not reconized in stretch configuration
That probably means that Linux is not seeing the card as a parallel port.

But that may not matter and can even be for the better. Can you see the card listed anywhere with lspci -v?
If so what are the addresses listed?

Please Log in to join the conversation.

More
7 years 5 months ago #135308 by Philippe
Replied by Philippe on topic Problem parralel Port is not reconized in stretch configuration
see the message here after


2:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller (rev 02)
Subsystem: Hewlett-Packard Company Compaq 500B Microtower
Physical Slot: 33
Flags: bus master, fast devsel, latency 0, IRQ 26
I/O ports at d800
Memory at febff000 (64-bit, non-prefetchable) [size=4K]
Memory at fdff0000 (64-bit, prefetchable) [size=64K]
Expansion ROM at febc0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169

03:04.0 Communication controller: Device 9510:9805 (rev 01)
Subsystem: LSI Logic / Symbios Logic Device 0010
Flags: medium devsel, IRQ 10
I/O ports at ec00
I/O ports at e880
I/O ports at e800
I/O ports at e480
I/O ports at e400
I/O ports at e080

pilou@PilouCnc:~$

Please Log in to join the conversation.

More
7 years 5 months ago #135316 by Todd Zuercher
Replied by Todd Zuercher on topic Problem parralel Port is not reconized in stretch configuration
Try using the port address 0xec00 and/or 0xe480.

Please Log in to join the conversation.

More
7 years 5 months ago #135370 by Philippe
Replied by Philippe on topic Problem parralel Port is not reconized in stretch configuration
with 0xe480 or 0xec00 the parallel port is not found
How can I see if the parallel port is recognized by Linux

Please Log in to join the conversation.

More
7 years 5 months ago #135385 by andypugh
Replied by andypugh on topic Problem parralel Port is not reconized in stretch configuration

Philippe wrote: 03:04.0 Communication controller: Device 9510:9805 (rev 01)


This might be a parallel port.
www.pcilookup.com/?ven=&dev=9805&action=submit

But it seems that the vendor ID is maybe not known, so Linux can't tell what it is.
This might not matter to the hal parallel port driver, to an extent it does not care.

Can you copy and paste the exact "not found" error message? It's probably easiest from the terminal:
Code:
halrun loadrt hal_parport cfg="0xec00" show pin exit

Please Log in to join the conversation.

More
7 years 5 months ago #135400 by Philippe
Replied by Philippe on topic Problem parralel Port is not reconized in stretch configuration
see here after
pilou@PilouCnc:~$ halrun
halrun: Realtime already running. Use 'halrun -U' to stop existing realtime session.
pilou@PilouCnc:~$ loadrt hal_parport cfg="0xec00"
bash: loadrt : commande introuvable
pilou@PilouCnc:~$

Please Log in to join the conversation.

More
7 years 5 months ago #135401 by andypugh
Replied by andypugh on topic Problem parralel Port is not reconized in stretch configuration
OK, do this without LinuxCNC running

(Though, if the parport isn't found, how is it that LinuxCNC is running?)

Please Log in to join the conversation.

More
7 years 5 months ago #135402 by Philippe
Replied by Philippe on topic Problem parralel Port is not reconized in stretch configuration
i don't know

Please Log in to join the conversation.

More
7 years 5 months ago #135404 by Philippe
Replied by Philippe on topic Problem parralel Port is not reconized in stretch configuration
when i put the parallel port in my Hal file linuxcnc run with a error message

Attachment not found

Please Log in to join the conversation.

Time to create page: 0.083 seconds
Powered by Kunena Forum