Profile for SrLange61

Offline

User Type: User
Rank: Junior Member

Register Date: 15 Jun 2013
Last login: 3 months 1 day ago
Time Zone: UTC +11:00
Local Time: 10:08

Posts: 33
Profile views: 8

Gender: Unknown
Birthdate: Unknown

SrLange61's recent posts (33 messages )

	Subject	Replies / Views	Last Post

	issues with isolcpus Category: General LinuxCNC Questions Topic started 9 months 3 days ago, by mrmike Last Post 9 months 3 days ago by mrmike	Replies:3 Views:617	Last Post by mrmike 9 months 3 days ago
	Latency, error finishing read, and IRQ affinity Category: General LinuxCNC Questions Topic started 2 years 8 months ago, by mozmck Last Post 19 hours 36 minutes ago by tommylight 1 2 3 ... 7	Replies:69 Views:46.4k	Last Post by tommylight 19 hours 36 minutes ago
	7i92 cnc motion controller from aliexpress? Category: Driver Boards Topic started 11 months 2 weeks ago, by Reyes Last Post 4 months 1 week ago by PCW 1 2 3	Replies:24 Views:6073	Last Post by PCW 4 months 1 week ago
	Latency High with 2.9.3 on older PC Category: Computers and Hardware Topic started 1 year 10 months ago, by Oops Last Post 1 year 9 months ago by SrLange61	Replies:2 Views:1308	Last Post by SrLange61 1 year 9 months ago
	execv(python): No such file or directory / python working directory Category: Advanced Configuration Topic started 4 years 1 day ago, by chili023 Last Post 2 years 10 months ago by Dieter 1 2	Replies:14 Views:4581	Last Post by Dieter 2 years 10 months ago
	[ Vfdmod ] An easy VFD control over MODBUS RTU Category: HAL Topic started 6 years 6 months ago, by aekhv Last Post 9 months 4 weeks ago by xenon-alien 1 2 3 ... 17	Replies:162 Views:75.1k	Last Post by xenon-alien 9 months 4 weeks ago
	Driver+Firmware+PCB for Pi RP2040 PIO (i.e. an easy-to-configure FPGA-like card) Category: Driver Boards Topic started 4 years 2 months ago, by edamametech Last Post 3 years 7 months ago by Bari 1 2	Replies:14 Views:7804	Last Post by Bari 3 years 7 months ago
	New compensation component for engraving and 3D Printing Category: Advanced Configuration Topic started 6 years 5 months ago, by scotta Last Post 3 years 7 months ago by ljkenny 1 2 3 4	Replies:34 Views:18k	Last Post by ljkenny 3 years 7 months ago
	adding auto leveling to linuxCnc Category: General LinuxCNC Questions Topic started 5 years 7 months ago, by Ewok2 Last Post 3 years 5 months ago by matti.juntunen 1 2 3 4	Replies:39 Views:20.8k	Last Post by matti.juntunen 3 years 5 months ago
	adding auto leveling to linuxCnc Category: General LinuxCNC Questions Topic started 5 years 7 months ago, by Ewok2 Last Post 3 years 5 months ago by matti.juntunen 1 2 3 4	Replies:39 Views:20.8k	Last Post by matti.juntunen 3 years 5 months ago

Time to create page: 0.129 seconds

Powered by Kunena Forum