Search Results (Searched for: )

  • tommylight
26 May 2026 03:25
Replied by tommylight on topic need help with ethercat vs mesa
Yes, as far as i can recall.
  • timo
26 May 2026 03:12 - 26 May 2026 03:13
Replied by timo on topic need help with ethercat vs mesa
Just a general question. Does a mixed system work? Put the basics on the Mesa card and, if needed, extend with Ethercat?
  • tommylight
26 May 2026 03:06
Replied by tommylight on topic Ethernet connection to Mesa 7i76e disconnecting on its own after one minute
Can you power off the machine and leave only Mesa powered?
  • spumco
26 May 2026 02:53
Replied by spumco on topic Stepperonline A6 Ethercat - Digital IO [SOLVED]
I found the following in the generic xml file from the Stepperonline site:
Warning: Spoiler!


I tried changing sub-index 1 to bit 4, and that sent a value of '16' to the drive.
Also changed sub-index 2 to bits 4&5, resulting in two HAL pins.  When I turned both of those on the drive reported "48" in the 'Enable Physical Output' field.

No output turned on.

Maybe there's some way to interpret this to figure out what the values are?
  • RMJ fabrication
26 May 2026 02:19
Replied by RMJ fabrication on topic Ethernet connection to Mesa 7i76e disconnecting on its own after one minute
I did not try another LAN cable.
The machine and PC are grounded properly.
I dont have a DVM at the moment but as soon as I get one I will measure those.
I believe this is a software issue because even with qtplasmac not running I get the disconnected error every 45 seconds
 
  • tommylight
26 May 2026 01:58
Replied by tommylight on topic Ethernet connection to Mesa 7i76e disconnecting on its own after one minute
Did you try another LAN cable?
Is the machine and the PC grounded properly?
Use a DVM and measure between Mesa 24V GND and machine case, in AC mode, while the machine is ON, post result.
  • tommylight
26 May 2026 01:54
Replied by tommylight on topic Hurco BMC 30 AP
Those seem like two separate issues, one remap is not doing OK and the other complaining about gcode, are you running the default "Linux CNC" gcode?
  • spumco
26 May 2026 01:53
Replied by spumco on topic Stepperonline A6 Ethercat - Digital IO [SOLVED]
<pdoEntry idx="60FD" subIdx="2" bitLen="32" halType="complex">

does control the enable - or at least whatever that line in the object dictionary refers to.

I have no problem sending values to the drive, and can change the value by changing the bits and 'padding' in xml file.

What I don't know is which bit(s) - what value - the drive requires to turn the outputs on.  As I mentioned earlier I've mapped bits 1 & 2 to both sub-index 1 and sub-index 2 and turned both 'on.'  Tried the same thing for bits 16 & 17.

I guess I could just brute-force it and try ALL the 32 bits for botrh sub-indexes.
  • RMJ fabrication
26 May 2026 01:52
Replied by RMJ fabrication on topic Ethernet connection to Mesa 7i76e disconnecting on its own after one minute
 
  • tommylight
26 May 2026 01:50
Replied by tommylight on topic LinuxCNC mit ProbeBasic bleibt einfach setehen
Ist die machine ge-erdet?
Ist die PC ge-erdet?
Beiden mussen sein.
Lauf gcode ohne die spindel (spindel auss geschaltet), pasiert die selbe fehler?
  • PCW
26 May 2026 01:38
Replied by PCW on topic Ethernet connection to Mesa 7i76e disconnecting on its own after one minute
Sounds like host or 7I76E issues

Whats does

ip a

report?
 
  • rodw
26 May 2026 01:30
Replied by rodw on topic Stepperonline A6 Ethercat - Digital IO [SOLVED]
oops should be
Code:
<pdoEntry idx="60FD" subIdx="1" bitLen="32" halType="complex">

Also
<pdoEntry idx="60FD" subIdx="2" bitLen="32" halType="complex"> seems like it will control whether the IO is enabled or not
  • rodw
26 May 2026 01:24
Replied by rodw on topic Stepperonline A6 Ethercat - Digital IO [SOLVED]
To test output , connect one output to your coolant in hal and see if it triggers.
  • rodw
26 May 2026 01:23
Replied by rodw on topic Stepperonline A6 Ethercat - Digital IO [SOLVED]
ok, seems its like
Code:
<syncManager idx="3" dir="in"> <pdo idx="1a00"> ....... <pdoEntry idx="60FD" subIdx="0" bitLen="32" halType="complex"> <complexEntry bitLen="1" halPin="CW-limit" halType="bit"/> <complexEntry bitLen="1" halPin="CCW-limit" halType="bit"/> <complexEntry bitLen="1" halPin="in-home" halType="bit"/> <complexEntry bitLen="13"/> <complexEntry bitLen="1" halPin="in-1" halType="bit"/> <complexEntry bitLen="1" halPin="in-2" halType="bit"/> <complexEntry bitLen="1" halPin="in-3" halType="bit"/> <complexEntry bitLen="1" halPin="in-4" halType="bit"/> <complexEntry bitLen="1" halPin="in-5" halType="bit"/> <complexEntry bitLen="1" halPin="in-6" halType="bit"/> <complexEntry bitLen="10"/> </pdoEntry> </pdo>

Keep the rest of the entries there. Things like status words are important
Also make sure the total bits adds up to 32, pad out unused ones
 
  • RMJ fabrication
26 May 2026 00:31
Replied by RMJ fabrication on topic Ethernet connection to Mesa 7i76e disconnecting on its own after one minute
 
Displaying 3676 - 3690 out of 11908 results.
Time to create page: 0.173 seconds
Powered by Kunena Forum