Search Results (Searched for: )

  • tommylight
16 May 2026 14:24
Replied by tommylight on topic Detailed FreeCAD 1.1 tutorial by DeltaHedra on youtube.
Bump to remove it from the "no replies" list.
  • tommylight
16 May 2026 14:22
Replied by tommylight on topic Spindle configuration

Hello,

few days ago my laptop died
Does the hard drive still work?
If yes, yank it out and put it in the new PC, it should work without installing anything and the machine should work as before.
If the install has failed, you can use a USB stick with any Live Linux to read the existing config and copy it to another USB, then to the new PC.
Or just check what pin setup you had there.
  • PCW
16 May 2026 13:37
Replied by PCW on topic 7i76D Spindle Analog output changed overnight!
Did you check the the analog command (xx.n.7i76.0.0.spinout) in hal is as expected?
that is 1000 for a 1000 RPM command with a scale of 10000
(in case you have feedback in the PID setup and there is a encoder issue)

If the analog spindle output (when disconnected from the VFD) is non-linear
relative to xx.n.7i76.0.0.spinout pin, it likely means the the OP-AMP buffer
in the analog output circuit has been damaged, perhaps by EMI from the VFD
  • harindugamlath
16 May 2026 12:19
Replied by harindugamlath on topic 7i76D Spindle Analog output changed overnight!
At lower end it's about twice the voltage, then the error gets lower as we go up. I also noticed spindle rpm glitching once. I have an encoder and had setup spindle at speed with that, That's how I noticed first. Then measured the voltages.
  • tommylight
16 May 2026 11:53
Replied by tommylight on topic 7i76D Spindle Analog output changed overnight!
Even in this fuzzy state i do not think it is the board, i have over 70 or 80 (probably more) of them in daily use for over 10 years and none ever failed nor any hiccups nor any issues ever.
I'll shut up now ...
Then again moisture does cause issues ...
:)
  • tommylight
16 May 2026 11:49
Replied by tommylight on topic Mill Retrofit with Fanuc DC Drives
No not twisted for that, shielded, RG58 or RG59 antenna cable if you do not have anything thinner.
Twisted cables are not for analog use.
  • tbrasselle
16 May 2026 11:43 - 16 May 2026 11:47
Replied by tbrasselle on topic Mill Retrofit with Fanuc DC Drives
I am in the US. That vibration on analogout3 is the million dollar question. If I disconnect the wires on analogout0 the vibration completely goes away on analogout3.

I am using original wiring except for 8-10inches of twisted pairs for both analog signals to connect the original wiring to the mesa boards.
  • harindugamlath
16 May 2026 11:43
Replied by harindugamlath on topic 7i76D Spindle Analog output changed overnight!
Let's wait for PCW I guess. There's no way I can get a replacement for this fast enough. If I can repair it it will be a great help.
  • tommylight
16 May 2026 11:33
Replied by tommylight on topic 7i76D Spindle Analog output changed overnight!

I Think you didn't get that it's voltage output that has changed.
Oh i did, but being deprived of sleep for 3 days and having now slept for 11 hours is messing my head up badly, so i urgently need a coffee or two.
Sorry.
  • tommylight
16 May 2026 11:30 - 16 May 2026 11:37
Replied by tommylight on topic Mill Retrofit with Fanuc DC Drives
Another look and...you are in US, that looks like 60Hz noise.
Edit:
I need a coffee or two, but still, why is that vibration on analogout3?
  • tbrasselle
16 May 2026 11:26
Replied by tbrasselle on topic Mill Retrofit with Fanuc DC Drives
Thanks for the response! I’ve followed that outline pretty carefully but get stuck at setting P. It doesn’t matter what I set it to I can’t get rid of the vibration in the motor. If it’s too high or too low I get following errors but no value reduces the vibration to an acceptable level. The screenshot in the first post shows the minimum level of vibration I can get by changing P. I’ve tried increasing the dead band but that doesn’t seem to help unless it’s so big that it gives following errors.
  • harindugamlath
16 May 2026 11:08
Replied by harindugamlath on topic 7i76D Spindle Analog output changed overnight!
No. It's just as before. I Think you didn't get that it's voltage output that has changed. it's sending out 2V instead of 1V. This one has been untouched since 2021. Mesa card is acting up.
  • tommylight
16 May 2026 10:45
Replied by tommylight on topic 7i76D Spindle Analog output changed overnight!
Check the VFD, probably set at 0-5V instead of 0-10V.
  • harindugamlath
16 May 2026 08:04
7i76D Spindle Analog output changed overnight! was created by harindugamlath
Hi, This is a weird issue. For some reason analog output of the spindle of my 7i76D has changed overnight. It's roughly giving out twice the correct voltage at the low end and the error gets less at the top (10,000rpm)

This has worked fine since 2021 and I haven't touched any INI, HAL settings. Out of curiosity I measured the 10V power (which is bang on at 10.00V) and the output. If I command 1000rpm its giving out 2.1V which is way above. 0-10,000 rpm spindle (0-10V) It should be at around 1V @1000rpm right?
Never came across anything like this before. 

Is the digital potentiometer in the 7i76 failing? what should I do?
Displaying 3871 - 3885 out of 11907 results.
Time to create page: 0.447 seconds
Powered by Kunena Forum