Search Results (Searched for: )

  • meister
12 May 2026 09:37
HalView was created by meister
little tool to see the hal-values in realtime:

  • northernstepper
12 May 2026 03:37
Replied by northernstepper on topic Stepper Driver Enable Pin
Will do thank you. How would they be connected to estop, for future reference
  • Venker
12 May 2026 03:15
Replied by Venker on topic LINUXCNC TURN
BTW linux 2.9.1 version
and new fusion linux cnc version

Also some guidance on troubleshooting issues "like" this would be deeply appreciated.
  • rodw
12 May 2026 03:14
Replied by rodw on topic Stepper Driver Enable Pin
They are actually disable pins, not ensable. Its best to leave them disconnected as you have enough to worry about for now. Sometimes they are useful for estop but as Tommy says leave well alone for now;
  • Venker
12 May 2026 03:13
LINUXCNC TURN was created by Venker
I’m having a lot of trouble configuring my LinuxCNC turn profile with Fusion 360. Could someone explain how they set theirs up? Does the standard post/profile work properly on your machine? I keep running into a ton of errors, even when trying the example files. Any guidance or working configurations would be really appreciated.
  • tommylight
12 May 2026 03:07
Replied by tommylight on topic Stepper Driver Enable Pin

Or should I leave them unconnected.
Yes, at least for now, till you get the machine working properly.
  • Twitchy88
12 May 2026 02:57
Replied by Twitchy88 on topic GRUB bootloader failed
Thanks for the help.

Installing it on another computer worked. At first it gave the same error because it didnt have the drivers for the wireless card. Plugged it in and it installed no problem.  Im wondering if I wasnt getting internet on the cnc, it said it connected successfully and internet worked when I booted live.
  • northernstepper
12 May 2026 02:44
Stepper Driver Enable Pin was created by northernstepper
Hello all, I have a question about the enable pin on my stepper drivers, I have 4x DM542T stepper drivers from Stepper Online connected to my Mesa 7i76EU. Is it recommended to connect the enable pins to the Mesa, and if so where should they be connected to. Or should I leave them unconnected.
  • grijalvap
12 May 2026 02:30
Replied by grijalvap on topic Best way to do external controls for LinuxCNC
Any bpdy in the forum heve used this gRPC

github.com/dougcalobrisi/linuxcnc-grpc

not sure if it is real time but I think is an interesting aproach sinse GRPC is lenguaje agnostic 
prety well supported and i think the c++ or RUST version can run deterministic
  • grandixximo
12 May 2026 02:11
Replied by grandixximo on topic LinuxCNC S-Curve Accelerations
Should be fixed
  • Twitchy88
12 May 2026 02:02
Replied by Twitchy88 on topic GRUB bootloader failed
I guess I could try. Little bit harder as im using a m.2 ssd
  • tommylight
12 May 2026 01:57
Replied by tommylight on topic GRUB bootloader failed
Do you have another PC that you can use to install?
You can put the hard drive from this PC into another PC, install it there, then move it back to this PC.
Usually it works first try, granted it does install on the other PC.
Make sure to disconnect the hard drives on the other PC before all this to prevent accidentally wiping it.
  • Twitchy88
12 May 2026 01:31
Replied by Twitchy88 on topic GRUB bootloader failed
Any more suggestions? I've now wasted another night after work trying to do this.  I've downloaded the iso again and put it on a different stick. Updated bios. Confirmed internet via live.
  • tommylight
11 May 2026 18:28
Replied by tommylight on topic Water depth, slats, and underwater cutting
I do recall seeing those plates ... :)
  • rodw
11 May 2026 18:02
Replied by rodw on topic Water depth, slats, and underwater cutting
Welcome back Arcsynapse89! 
Displaying 3811 - 3825 out of 11383 results.
Time to create page: 0.188 seconds
Powered by Kunena Forum