Mesa in Australia?

Johns price for the cards was the same for the 2 in the package with lead. Mesa shipped the next day but the international shipping charge was US61.00 which is almost 100 bucks aussie with the exchange rate. That was the sting in the tail but I wouldnt have paid it if I didnt think it was worth it. The cards were packed well though. Nice looking cards, well made too. I am happy with what I got but next time I will get them from John. I have plans for a couple more machines and I think this is what they will all be based on going by all the researching I have done on LCNC

For packages under $400 you can ship First Class International for about $25 and it rides on the same airplane to Australia as Priority.

JT

I'd just like to add my vote of confidence for Big John's Mesa store. I'm based in Brisbane, Australia and I thought the shipping price was very reasonable and the parts arrived in good time. Not only that John gave me a bit of advice and shared some files over a few emails which was very much appreciated.

John did say he could not wait to see my plasma up and running but sadly for John, the Mesa cards are still in the box while I have been building the machine from scratch. The Z is done, the Y is half done but I've changed the design a few times and I think I have settled on the final design today but have to get it drawn up yet. So many little things to consider. Anyway, hopefully I'll be onto the electronics in a few weeks so get ready for a raft of noob question on the forum..

Where in Brissy are you? I am at Burpengary. Just got LCNC fired up on a computer...latency doesnt look that good on it but will have to read the manuals on. Made a file up on fusion360 and mach loads it fine but LCNC says it has a error with not being able to find a tool so no doubt I will be asking some questions in another thread . I want to get across LCNC and its functions before hooking it up to my machine first off by the parallel port then once I get it working then I will put the 5I25 and sort that then fit the 7I76 to the machine

"Spectre wrote: Where in Brissy are you? I am at Burpengary. Just got LCNC fired up on a computer...latency doesnt look that good on it but will have to read the manuals on. Made a file up on fusion360 and mach loads it fine but LCNC says it has a error with not being able to find a tool so no doubt I will be asking some questions in another thread . I want to get across LCNC and its functions before hooking it up to my machine first off by the parallel port then once I get it working then I will put the 5I25 and sort that then fit the 7I76 to the machine

I'm at Algester on the other side of town. My contact details are here

Funny, I've been running latency tests tonight as well while wading through the 700 page LCNC manual. I think I read somewhere that you need to set up the tools in LCNC to get them to work.. Latency is sitting on about 19,000 on an old MiniBox industrial PC so it should be fine with the 7i76E card with hardware step gen. I could never get it talking to a parallel port BOB hence my move to Mesa..

Rod

I have setup a new machine with a PMDX-126 and a PMDX-107 and running on Mach 3 to make sure all the functions work as they should. Next is to get a LCNC PC to run out of the parallel port to the 126 and get used to LCNC then replace that port with the 5I25 to run as a parallel port make sure it all works still then take out the 126 and run the 7I76 in the machine. Learning LCNC seems to be the trick so far. I have a file that works on Mach3 but when I load it into LCNC it comes up with a missing tool number error. This maybe something I have done in Fusion 360 so going back to that first to make sure I have done all the CAM properly . Reading the LCNC manual is certainly some work there is a stack of info there you have to get your head around. I havent connected the LCNC PC yet to the machine but hopefully later this week