7i96 debug
- Gaunt1969
- Offline
- Senior Member
-
Less
More
- Posts: 45
- Thank you received: 8
30 Jan 2020 04:04 - 30 Jan 2020 04:04 #156137
by Gaunt1969
7i96 debug was created by Gaunt1969
I am setting up a 7i96 and have gone thru the pncconf and made a setup. When I launch my setup it fails to load and the debug error states "cant find module 'hm2_eth'. What do I need to get the module loaded?
Last edit: 30 Jan 2020 04:04 by Gaunt1969.
Please Log in or Create an account to join the conversation.
- AgentWD40
-
- Offline
- Platinum Member
-
Less
More
- Posts: 334
- Thank you received: 93
30 Jan 2020 05:07 #156141
by AgentWD40
Replied by AgentWD40 on topic 7i96 debug
Posted earlier today
forum.linuxcnc.org/9-installing-linuxcnc...mware-missing#156122
forum.linuxcnc.org/9-installing-linuxcnc...mware-missing#156122
The following user(s) said Thank You: Gaunt1969
Please Log in or Create an account to join the conversation.
- tommylight
-
- Away
- Moderator
-
Less
More
- Posts: 20860
- Thank you received: 7113
30 Jan 2020 10:58 #156156
by tommylight
Replied by tommylight on topic 7i96 debug
You will need the preempt-RT version of Linuxcnc for ethernet, not the RTAI version.
It is on the diwnloads page as Stretch, not Wheezy.
It is on the diwnloads page as Stretch, not Wheezy.
The following user(s) said Thank You: Gaunt1969
Please Log in or Create an account to join the conversation.
- Gaunt1969
- Offline
- Senior Member
-
Less
More
- Posts: 45
- Thank you received: 8
31 Jan 2020 01:43 - 31 Jan 2020 01:44 #156224
by Gaunt1969
Replied by Gaunt1969 on topic 7i96 debug
now i am at a loss. What am i missing?
I installed a version of strech and upgraded to master rt, with uname -a i get
Linux CNC 4.9.0-11-rt-686-pae #1 SMP PREEMPT RT Debian 4.9.189-3 (2019-09-02) i686 GNU/Linux.
in Pncconf i no longer have and option of Gmocappy for the Gui and the big thing is there is no option for the 7i96 in the card options. Any Ideas?
I installed a version of strech and upgraded to master rt, with uname -a i get
Linux CNC 4.9.0-11-rt-686-pae #1 SMP PREEMPT RT Debian 4.9.189-3 (2019-09-02) i686 GNU/Linux.
in Pncconf i no longer have and option of Gmocappy for the Gui and the big thing is there is no option for the 7i96 in the card options. Any Ideas?
Last edit: 31 Jan 2020 01:44 by Gaunt1969.
Please Log in or Create an account to join the conversation.
- PCW
-
- Offline
- Moderator
-
Less
More
- Posts: 17380
- Thank you received: 5067
31 Jan 2020 02:28 #156229
by PCW
Replied by PCW on topic 7i96 debug
You need to install the LinuxCNC 2.8 for 7I96 support (and 2.9 is better)
(and you need the uspace version of LinuxCNC)
(and you need the uspace version of LinuxCNC)
Please Log in or Create an account to join the conversation.
- Gaunt1969
- Offline
- Senior Member
-
Less
More
- Posts: 45
- Thank you received: 8
31 Jan 2020 03:23 #156231
by Gaunt1969
Replied by Gaunt1969 on topic 7i96 debug
If I wasn't lost I would not know where I am at.
And I know right where I am.
Lost as can be.
I cant seem to get it correct in the package manager to get it to install.
And I know right where I am.
Lost as can be.
I cant seem to get it correct in the package manager to get it to install.
Please Log in or Create an account to join the conversation.
- tommylight
-
- Away
- Moderator
-
Less
More
- Posts: 20860
- Thank you received: 7113
31 Jan 2020 12:51 #156247
by tommylight
Replied by tommylight on topic 7i96 debug
Follow the instructions on
Buildbot.linuxcnc.org
Buildbot.linuxcnc.org
Please Log in or Create an account to join the conversation.
- andypugh
-
- Offline
- Moderator
-
Less
More
- Posts: 19678
- Thank you received: 4559
11 Feb 2020 13:09 #157045
by andypugh
Did you solve this?
Replied by andypugh on topic 7i96 debug
I cant seem to get it correct in the package manager to get it to install.
Did you solve this?
Please Log in or Create an account to join the conversation.
Moderators: PCW, jmelson
Time to create page: 0.115 seconds