Optiplex 755

zz912
Topic Author
Offline
Platinum Member

07 Mar 2023 19:07 #266055 by zz912

Replied by zz912 on topic Optiplex 755

jarda@CNC1:~$ sudo chrt 99 ping -i .001 -q 10.10.10.10
PING 10.10.10.10 (10.10.10.10) 56(84) bytes of data.
^C
--- 10.10.10.10 ping statistics ---
253024 packets transmitted, 253023 received, 0.000395219% packet loss, time 276ms
rtt min/avg/max/mdev = 0.164/0.253/0.539/0.012 ms
jarda@CNC1:~$

I have to go home right now. I can do more tests tomorrow.

Please Log in or Create an account to join the conversation.

zz912
Topic Author
Offline
Platinum Member

08 Mar 2023 05:25 #266093 by zz912

Replied by zz912 on topic Optiplex 755

Optiplex 7010
I made same test with Optiplex 7010 at home.

Coalescing Disabled
It is better, but first test is wrong too.

Please Log in or Create an account to join the conversation.

zz912
Topic Author
Offline
Platinum Member

09 Mar 2023 09:38 #266185 by zz912

Replied by zz912 on topic Optiplex 755

I would like to ask what these tests mean? Do I have a weak PC? Or is there a bug somewhere (LCNC, kernel, debian ....)?

Please Log in or Create an account to join the conversation.

rodw
Offline
Platinum Member

09 Mar 2023 11:27 #266200 by rodw

Replied by rodw on topic Optiplex 755

try this command

latency-histogram --nobase --sbins 1000

as PCW said there is no need to look at the base thread as it is not used with a mesa card.

the histogram shows the jitter which is the time a thread is late or early. If there is too much jitter, the servo-thread will not get finished before the next one starts... which is a latency error...

Please Log in or Create an account to join the conversation.

zz912
Topic Author
Offline
Platinum Member

09 Mar 2023 12:44 - 09 Mar 2023 13:42 #266205 by zz912

Replied by zz912 on topic Optiplex 755

1) I understand, that I can ignore Base thread. I didn't realize that 25000 in the error message means that the error is in basethread and not in servothead.

2) My main question is, can I ignore the PC test in the MesaCT configurator?

3) I will try latency-histogram

Last edit: 09 Mar 2023 13:42 by zz912.

Please Log in or Create an account to join the conversation.

PCW
Away
Moderator

09 Mar 2023 15:01 #266214 by PCW

Replied by PCW on topic Optiplex 755

I think there is a bug in mesact

The servo thread tmax should show 75%

(100*1747291/2333333)

If you have disabled all power saving options in the CPU
and have Interrupt coalescing off you may have to run at a lower
servo thread rate on that PC (say 2 ms period instead of 1 ms)

The following user(s) said Thank You: zz912

Please Log in or Create an account to join the conversation.

zz912
Topic Author
Offline
Platinum Member

09 Mar 2023 15:33 #266217 by zz912

Replied by zz912 on topic Optiplex 755

I had 3 problems:
1) MesaCT - I'm going to assume it's wrong.
2) Latency message error - now I know, that it is BaseThread
3) SSerial error - Maybe turning off the AMT setup will help. I will keep an eye out to see if the error reappears.

Please Log in or Create an account to join the conversation.

zz912
Topic Author
Offline
Platinum Member

10 Mar 2023 16:05 #266298 by zz912

Replied by zz912 on topic Optiplex 755

Yesterday I celebrated that turning off AMT solved my problem. Today I came to the PC and again it is causing problems.

Please Log in or Create an account to join the conversation.

PCW
Away
Moderator

10 Mar 2023 16:22 #266300 by PCW

Replied by PCW on topic Optiplex 755

I would try a 2 ms servo thread period

Please Log in or Create an account to join the conversation.

zz912
Topic Author
Offline
Platinum Member

10 Mar 2023 17:23 #266307 by zz912

Replied by zz912 on topic Optiplex 755

2 ms did not help:

Mabey evengravy have solution:
forum.linuxcnc.org/38-general-linuxcnc-q...2-8-4-stretch#266292

It's strange that I had no problems yesterday.

Please Log in or Create an account to join the conversation.

Moderators: PCW, jmelson

Time to create page: 0.185 seconds

Optiplex 755

Attachments:

Attachments:

Attachments:

Attachments: