7i77 analog out 5
15 Feb 2019 13:10 #126535
by mpvriens
7i77 analog out 5 was created by mpvriens
Hello, have a question, have an output for my spindle on analog output 5 of the Mesa 7i77 card, if i measure voltage at rpm 1000 I measure 5 volt output, but if i connect the output to the 0 to 10 volt input of a simodrive 6DV5.5 the output drops to 0,0 voltage. the input has ( by the manual ) an 10K input resistance)
The other analog outputs keep there value a i still can jog around.
If i put a battery of 1.5 volt to the input of the simodrive, he runs fine.
The other analog outputs keep there value a i still can jog around.
If i put a battery of 1.5 volt to the input of the simodrive, he runs fine.
Please Log in or Create an account to join the conversation.
15 Feb 2019 14:36 #126543
by PCW
Replied by PCW on topic 7i77 analog out 5
Did you measure at the 7I77? You may have a wiring issue or missing ground
Please Log in or Create an account to join the conversation.
15 Feb 2019 15:09 #126550
by mpvriens
Replied by mpvriens on topic 7i77 analog out 5
Have measured at pin 23 and 24 on TB5 of the 7i77
and have only two wires connected to the simodrive ground and Aout5 to :
"sollwert" and "0volt"
No extra ground
and have only two wires connected to the simodrive ground and Aout5 to :
"sollwert" and "0volt"
No extra ground
Please Log in or Create an account to join the conversation.
15 Feb 2019 15:15 #126551
by PCW
Replied by PCW on topic 7i77 analog out 5
One possibiiity is swapped pins. This would ground
the 7I77 analog output.
the 7I77 analog output.
Please Log in or Create an account to join the conversation.
15 Feb 2019 15:20 #126553
by mpvriens
Replied by mpvriens on topic 7i77 analog out 5
swapped the cable: no result: same output
Please Log in or Create an account to join the conversation.
15 Feb 2019 15:23 - 15 Feb 2019 15:24 #126554
by PCW
Replied by PCW on topic 7i77 analog out 5
I would check the 7I77 analog output by itself
and then check the cable:
(Ohm out at 7I77 end unconnected to 7I77 but connected to drive)
it should show 10K ohms or higher between the pins
and then check the cable:
(Ohm out at 7I77 end unconnected to 7I77 but connected to drive)
it should show 10K ohms or higher between the pins
Last edit: 15 Feb 2019 15:24 by PCW.
Please Log in or Create an account to join the conversation.
15 Feb 2019 15:34 #126557
by mpvriens
Replied by mpvriens on topic 7i77 analog out 5
after swapping the + and - don't have any output on the 7i77 anymore
with the halmeter it shows 300 at 300 rpm
with the halmeter it shows 300 at 300 rpm
Please Log in or Create an account to join the conversation.
15 Feb 2019 15:38 #126559
by mpvriens
Replied by mpvriens on topic 7i77 analog out 5
At the drive input i measure a high impedance >10Kohm
Please Log in or Create an account to join the conversation.
15 Feb 2019 15:42 #126561
by PCW
Replied by PCW on topic 7i77 analog out 5
I would measure at the 7I77 end (disconnect the plug)
s
s
Please Log in or Create an account to join the conversation.
15 Feb 2019 15:50 #126562
by mpvriens
Replied by mpvriens on topic 7i77 analog out 5
measuring on the input of the driver i measure a very low resistence (allmost short)
Please Log in or Create an account to join the conversation.
Time to create page: 0.164 seconds