Mesa 7i76e => hm2_eth: Unrecognized ethernet board
24 Nov 2015 16:14 - 24 Nov 2015 16:15 #65737
by PCW
Replied by PCW on topic Mesa 7i76e => hm2_eth: Unrecognized ethernet board
Heres a Linux version of the setname program:
freeby.mesanet.com/setname
export PROTOCOL=direct
export INTERFACE=elbp16
export IPADDR=192.168.1.121
./setname 7I76E-16
setname is statically linked so should run on most linux systems
freeby.mesanet.com/setname
export PROTOCOL=direct
export INTERFACE=elbp16
export IPADDR=192.168.1.121
./setname 7I76E-16
setname is statically linked so should run on most linux systems
Last edit: 24 Nov 2015 16:15 by PCW. Reason: fix url
The following user(s) said Thank You: sirhc
Please Log in or Create an account to join the conversation.
24 Nov 2015 18:38 #65751
by sirhc
Replied by sirhc on topic Mesa 7i76e => hm2_eth: Unrecognized ethernet board
That worked for me! Thanks
Please Log in or Create an account to join the conversation.
25 Nov 2015 13:31 - 25 Nov 2015 13:31 #65773
by jtc
Replied by jtc on topic Mesa 7i76e => hm2_eth: Unrecognized ethernet board
Worked on windows version. Finally have a working configuration running.
Last edit: 25 Nov 2015 13:31 by jtc.
Please Log in or Create an account to join the conversation.
03 Dec 2015 16:59 #66294
by OPS
Replied by OPS on topic Mesa 7i76e => hm2_eth: Unrecognized ethernet board
I've bought my board recently too, changed name by setname, but the board still not visible imho. I'm still getting error
Unsupported ethernet device ���������������� at 192.168.1.121
No 7I76E-16 board found![:( :(](/media/kunena/emoticons/sad.png)
Could you suggest how to fix this?
Regards,
Oleg
Unsupported ethernet device ���������������� at 192.168.1.121
No 7I76E-16 board found
![:( :(](/media/kunena/emoticons/sad.png)
Could you suggest how to fix this?
Regards,
Oleg
Please Log in or Create an account to join the conversation.
03 Dec 2015 17:02 - 03 Dec 2015 17:05 #66297
by PCW
Replied by PCW on topic Mesa 7i76e => hm2_eth: Unrecognized ethernet board
Did you power cycle the 7I76E after running setname?
(The card name is stored in EEPROM which is only read at power up or soft reset)
(The card name is stored in EEPROM which is only read at power up or soft reset)
Last edit: 03 Dec 2015 17:05 by PCW.
The following user(s) said Thank You: OPS
Please Log in or Create an account to join the conversation.
03 Dec 2015 17:08 #66298
by OPS
Replied by OPS on topic Mesa 7i76e => hm2_eth: Unrecognized ethernet board
YESS - that was the reason. I've just managed this and it works! Thaks for such a prompt reply!
Please Log in or Create an account to join the conversation.
03 Dec 2015 17:17 #66299
by OPS
Replied by OPS on topic Mesa 7i76e => hm2_eth: Unrecognized ethernet board
Sorry for offtop (( could you also suggest a link where to get a fresh firmware and sample configs for this board? Im running it on RT_PREEMP kernel amd_64 and my current firmware version 15. Thank you in advance,
Oleg
Oleg
Please Log in or Create an account to join the conversation.
03 Dec 2015 17:44 - 03 Dec 2015 18:01 #66301
by PCW
Replied by PCW on topic Mesa 7i76e => hm2_eth: Unrecognized ethernet board
Unless you need a config with additional daughtercards on the expansion connectors
the installed firmware should be fine (its the latest)
freeby.mesanet.com/7i76e.zip
is a minimal hal/ini config example file set
(note if you _just_ fetched this, refetch as the version on freeby was out of date and I just now updated it)
You may need to change the IP address in the .ini file
the installed firmware should be fine (its the latest)
freeby.mesanet.com/7i76e.zip
is a minimal hal/ini config example file set
(note if you _just_ fetched this, refetch as the version on freeby was out of date and I just now updated it)
You may need to change the IP address in the .ini file
Last edit: 03 Dec 2015 18:01 by PCW.
Please Log in or Create an account to join the conversation.
07 Jun 2017 15:25 #94237
by bymccoy
Replied by bymccoy on topic Mesa 7i76e => hm2_eth: Unrecognized ethernet board
How do you configure the 7i76e with daughter cards?
I have a 7i85 quad encoder on first port and plan in future to add a 7i76 on the second port.
Is this configured via firmware, onboard config or via the host software (LinuxCNC?)
Thanks!
I have a 7i85 quad encoder on first port and plan in future to add a 7i76 on the second port.
Is this configured via firmware, onboard config or via the host software (LinuxCNC?)
Thanks!
Please Log in or Create an account to join the conversation.
07 Jun 2017 15:59 #94244
by PCW
Replied by PCW on topic Mesa 7i76e => hm2_eth: Unrecognized ethernet board
You need to have firmware that matches the daughterboard set you have
for example, a 7I76E+7I85 would use 7i76e_7i76x1_7i85x1D.bit
firmware.
LinuxCNC would need to be configured to use the added encoders
for example, a 7I76E+7I85 would use 7i76e_7i76x1_7i85x1D.bit
firmware.
LinuxCNC would need to be configured to use the added encoders
Please Log in or Create an account to join the conversation.
Time to create page: 0.092 seconds