Advanced Search

tried to write the iso from the post above to a usb twice. Both times after selecting locale in the installer i get that a file failed to be copied

live enviroment works fine but the installer is not there

has anybody else tried it?

Ignore my stupidity - I have sorted the problem out.

I had though I was being clever in simplifying the HAL I was using, but to make it do what I wanted meant that the result was going to be more complex than the way I had already been doing things.

Great.
That all works.
You could also add "dro_axis_*" to the "button_response_list"
in the handler file so that these functions are not available during operation.

had still the oscillation.
But I dug myself a little deeper into the usage of pncconf with the discovery option and made a mint config file which I merged into my old config.
and the oscillation is gone and the axis are moving.

And just when I wanted to edit the post above when I saw you already answered.

here files which ware working now. also found out the the scale was wrong and adjusted it.
 

 

What are the specific issues you have now?

Here are the stylesheet properties, you can turn them on and off as you please.
They will change immediately.

Instead of binding this key to a button, is there a way to refresh the g-code file every few seconds while the g-code is not executing? I want to automatically load the g-code file into linuxcnc continuously. The name of the g-code file is always the same and never changes.

You will most probably have to reinstall everything.
In the networking HOWTO it is clearly stated to use that OR the /etc/network method, NEVER both!
You are using both. It also states to edit the existing wired connection, you did not, you added another one to the same interface.
Now you have 3 networks with the 2 of the same IP on a single interface, as you did not edit the existing one, but you added another one.
-
Try deleting every wired connection from the network manager and reboot.
If this does not work, reinstalling everything is the fastest way to get up and running, trying to fix this mess takes much longer.

OK, I switched ipv6 off in both networks, no effect. And I added the adress 10.10.10.2/24 in the four lines in etc/network/interfaces
Same issue as before. I'm asking me why there is this altname fault in ip a. I definitely have the right definitions in the two network settings, eno1 and eth2

(coming back later, have to bring the dog back to my son)

netmask is set to 10.10.10.2/24. Any alternative netmask? 

The only thing that I see is  different is the netmask

you might try

address 10.10.10.2/24

Also ipv6 has been enabled, which is really odd

Hmm I tried both, changed priorities eno1 to 1 and auto/enp2 to 0 - no effect.
Then I changed the position of the lines in /etc/network/interfaces - no effect at all.

On what reason ever, the network definitions are faulty.

WTF is going on there?

And this is ip a with the 4 lines in /etc/network/

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host noprefixroute
valid_lft forever preferred_lft forever
2: enp2s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
link/ether 00:0a:cd:00:00:56 brd ff:ff:ff:ff:ff:ff
inet 192.168.178.55/24 brd 192.168.178.255 scope global dynamic noprefixroute enp2s0
valid_lft 863931sec preferred_lft 863931sec
inet6 2003:ce:5f08:8600:6ae7:3d2d:fe1d:c940/64 scope global dynamic noprefixroute
valid_lft 7132sec preferred_lft 1118sec
inet6 fe80::d017:c5ae:2734:c531/64 scope link noprefixroute
valid_lft forever preferred_lft forever
3: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
link/ether 00:23:24:5b:b4:ac brd ff:ff:ff:ff:ff:ff
altname enp0s25
inet 10.10.10.2/8 brd 10.255.255.255 scope global eno1
valid_lft forever preferred_lft forever
inet6 fe80::223:24ff:fe5b:b4ac/64 scope link
valid_lft forever preferred_lft forever

why does it change the altname to enp0s25? that is a conflict with 2. where can I change the altname manually to fix this?
Or should I change the priorities so that eno1 is launched before enp2?

This is the feedback of ip a without the suggested lines:

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host noprefixroute
valid_lft forever preferred_lft forever
2: enp2s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
link/ether 00:0a:cd:00:00:56 brd ff:ff:ff:ff:ff:ff
inet 192.168.178.55/24 brd 192.168.178.255 scope global dynamic noprefixroute enp2s0
valid_lft 862758sec preferred_lft 862758sec
inet6 2003:ce:5f08:8600:6ae7:3d2d:fe1d:c940/64 scope global dynamic noprefixroute
valid_lft 7101sec preferred_lft 1700sec
inet6 fe80::d017:c5ae:2734:c531/64 scope link noprefixroute
valid_lft forever preferred_lft forever
3: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
link/ether 00:23:24:5b:b4:ac brd ff:ff:ff:ff:ff:ff
altname enp0s25
inet 10.10.10.2/24 brd 10.10.10.255 scope global noprefixroute eno1
valid_lft forever preferred_lft forever
 

I tested it a bit, it works very well.
I like it.
It could be everything even in one menu, axis button, but if it is possible to customize the content of both menus, it is very good.
How to do it in the style sheet?
In qtdragon_hd, the ref buttons are probably no longer needed? If so, I can customize the layout..

Marek