1. Forum
  3. Search

Advanced Search

Search Results (Searched for: )

  • spumco
  • spumco
08 Sep 2024 15:06 - 08 Sep 2024 15:08
Probe Basic - startup error on new installation was created by spumco

Probe Basic - startup error on new installation

Category: QtPyVCP

Just installed a fresh load of Debian 13 and followed the APT-installation instructions for Probe Basic.

One error reported during install (gpg keys, 'server error).

LCNC starts no problem.

On first run of the Probe Basic sim I get the following:

Warning: Spoiler! 

Switched from Development to Stable, same error.

Any ideas?
  • tommylight
  • tommylight's Avatar
08 Sep 2024 15:05
Replied by tommylight on topic Automatic Gantry Squaring

Automatic Gantry Squaring

Category: HAL

No component required, it is a normal feature since 2.8, see ini homing
linuxcnc.org/docs/html/config/ini-homing.html
Basically, set the HOME_SEQUENCE to -1 or -2 for the tandem joints in the ini file and adjust the HOME_OFFSET value as you need it to square properly.
PncConf will do this automatically if you choose a tandem axis/joint, probably StepConf will do the same but i am not sure.
  • tommylight
  • tommylight's Avatar
08 Sep 2024 15:01
Replied by tommylight on topic USB ports quit working?

USB ports quit working?

Category: Installing LinuxCNC

Yeah, i keep several PS2 keyboards around, just in case. :)
Although most PC i have do not have PS2... I miss that, no latency, not really noticeable except when gaming on arena shooters.
  • tommylight
  • tommylight's Avatar
08 Sep 2024 14:56
Replied by tommylight on topic Mesa 7i96 Output Wiring

Mesa 7i96 Output Wiring

Category: Driver Boards

---This has NOTHING to do with the subject, it is a public announcement to be careful on the internet!!!---

Those pictures are proof of how bad the internet has become, notice the L and N marks, that would imply mains voltage (110V or 220V) as L stands for a phase and N for neutral, yet this is for a low voltage DC equipment that clearly has marks + and - on the board.
  • tommylight
  • tommylight's Avatar
08 Sep 2024 14:51
Replied by tommylight on topic 7i97t with 7i85?

7i97t with 7i85?

Category: Driver Boards

www.welectron.com/Mesa-Electronics-DB25M...I-O-Extension-Boards
  • tommylight
  • tommylight's Avatar
08 Sep 2024 14:49
Replied by tommylight on topic What do you really get for a $350 desk top engraver ?

What do you really get for a $350 desk top engraver ?

Category: Show Your Stuff

Keep on chugging along, utmost respect for your persistence and effort.
  • spumco
  • spumco
08 Sep 2024 14:49
Replied by spumco on topic USB ports quit working?

USB ports quit working?

Category: Installing LinuxCNC

Thanks anyway Tommy.  Wouldn't have helped - keyboard & mouse quit working past the GRUB screen.  No way to type in "ls" comands or anythign else.
  • ekbiker
  • ekbiker
08 Sep 2024 14:48
Automatic Gantry Squaring was created by ekbiker

Automatic Gantry Squaring

Category: HAL

Does anyone have a .hal snippets for using gantry component in LinuxCNC 2.9.3 for automatic squaring in their homing sequence?
  • swepeter
  • swepeter
08 Sep 2024 14:40
Replied by swepeter on topic Mesa 7i96 Output Wiring

Mesa 7i96 Output Wiring

Category: Driver Boards

I believe they do. a led there at least 
  • PCW
  • PCW's Avatar
08 Sep 2024 14:29
Replied by PCW on topic Mesa 7i96 Output Wiring

Mesa 7i96 Output Wiring

Category: Driver Boards

That look correct as long as the valves have flyback diodes
(it looks like they do)
  • Aciera
  • Aciera's Avatar
08 Sep 2024 14:28
Replied by Aciera on topic Using a HAL pin in DH parameters

Using a HAL pin in DH parameters

Category: HAL

The pyvcp panel only exists after the gui has loaded, so you will need to put that line in the POSTGUI_HALFILE
  • PCW
  • PCW's Avatar
08 Sep 2024 14:26
Replied by PCW on topic 7i97t with 7i85?

7i97t with 7i85?

Category: Driver Boards

Yes, if the cable is HDR26F on one end and DB25M on the other
(the link does not work)
  • Abdulkareem
  • Abdulkareem
08 Sep 2024 14:25
Replied by Abdulkareem on topic Using a HAL pin in DH parameters

Using a HAL pin in DH parameters

Category: HAL

tried it but it gives this error  
  • swepeter
  • swepeter
08 Sep 2024 14:23
Replied by swepeter on topic Mesa 7i96 Output Wiring

Mesa 7i96 Output Wiring

Category: Driver Boards

I am a bit lost as well and the pictures are gone. Is this correct?Thanks so much  
  • Aciera
  • Aciera's Avatar
08 Sep 2024 14:19
Replied by Aciera on topic Using a HAL pin in DH parameters

Using a HAL pin in DH parameters

Category: HAL

Not sure if 'genserkins.A-0' is a pin or a parameter but try using 'net' instead of 'setp'
Displaying 21646 - 21660 out of 24808 results.
  1. Forum
  3. Search
Time to create page: 0.825 seconds
Powered by Kunena Forum