PnCConf Wizard 676 topics

Point n Click Configuration tool for Mesa Cards

Subject	Replies / Views	Last Post
Gantry System reversing direction of Motor on y2 Category: PnCConf Wizard Topic started 5 years 7 months ago, by Creative25 Last Post 5 years 7 months ago by Creative25	Replies:8 Views:2073	Last Post by Creative25 5 years 7 months ago
Help! Configuring Encoder Scale/Stepper Scale Category: PnCConf Wizard Topic started 5 years 7 months ago, by Sadmeatball Last Post 5 years 7 months ago by PCW	Replies:3 Views:2806	Last Post by PCW 5 years 7 months ago
PNCConf 2.90-pre0-3629g4fb5248dd (~03/03/2021) --- bug? (sorted) Category: PnCConf Wizard Topic started 5 years 7 months ago, by robertspark Last Post 5 years 7 months ago by cmorley	Replies:6 Views:1630	Last Post by cmorley 5 years 7 months ago
Calibrating Y and Y2 independently Category: PnCConf Wizard Topic started 5 years 7 months ago, by Creative25 Last Post 5 years 7 months ago by andypugh	Replies:3 Views:1674	Last Post by andypugh 5 years 7 months ago
HM2_ETH >> iptables >> hm2−eth−rules−output Category: PnCConf Wizard Topic started 5 years 8 months ago, by robertspark Last Post 5 years 7 months ago by robertspark 1 2	Replies:11 Views:4772	Last Post by robertspark 5 years 7 months ago
RPI4 + 7C81 + DMB4250-8B BreakOut Board Category: PnCConf Wizard Topic started 5 years 8 months ago, by brianvg Last Post 5 years 7 months ago by brianvg 1 2	Replies:15 Views:5223	Last Post by brianvg 5 years 7 months ago
pncconf a axis error Category: PnCConf Wizard Topic started 5 years 8 months ago, by johnbump Last Post 5 years 7 months ago by cmorley	Replies:3 Views:1414	Last Post by cmorley 5 years 7 months ago
gantry setup: X homing fine; Y-Y2 and Z not moving Category: PnCConf Wizard Topic started 5 years 8 months ago, by sibelius Last Post 5 years 8 months ago by tommylight	Replies:7 Views:1722	Last Post by tommylight 5 years 8 months ago
new 5i25, ordered without daughterboards: does it already have firmware loaded? Category: PnCConf Wizard Topic started 5 years 8 months ago, by johnbump Last Post 5 years 8 months ago by tommylight	Replies:1 Views:1329	Last Post by tommylight 5 years 8 months ago
7i96 pncconf issue? Category: PnCConf Wizard Topic started 5 years 8 months ago, by Bearfood Last Post 5 years 8 months ago by mrmike 1 2 3 ... 5	Replies:40 Views:9740	Last Post by mrmike 5 years 8 months ago
A bit of fog in the brain on Pncconf Wizard Category: PnCConf Wizard Topic started 5 years 8 months ago, by sibelius Last Post 5 years 8 months ago by sibelius	Replies:6 Views:1571	Last Post by sibelius 5 years 8 months ago
Error en PnCConf Category: PnCConf Wizard Topic started 5 years 8 months ago, by chuben Last Post 5 years 8 months ago by chuben	Replies:6 Views:1561	Last Post by chuben 5 years 8 months ago
No found 7i76e Category: PnCConf Wizard Topic started 5 years 9 months ago, by chuben Last Post 5 years 8 months ago by itsme 1 2 3	Replies:21 Views:6230	Last Post by itsme 5 years 8 months ago
PWM on 7i76E Category: PnCConf Wizard Topic started 5 years 8 months ago, by Philippe Last Post 5 years 8 months ago by Philippe	Replies:6 Views:2209	Last Post by Philippe 5 years 8 months ago
PnCConf stepper test tune works but changes are not accepted by Axis gui Category: PnCConf Wizard Topic started 5 years 9 months ago, by Captainjack Last Post 5 years 9 months ago by Captainjack	Replies:2 Views:1526	Last Post by Captainjack 5 years 9 months ago
[SOLVED] Bug: PnCConf does not set up servo spindle PID feedback correctly. Category: PnCConf Wizard Topic started 5 years 9 months ago, by FranseFrikandel Last Post 5 years 9 months ago by Steffen 1 2	Replies:11 Views:4354	Last Post by Steffen 5 years 9 months ago
pncconf 2.8 Category: PnCConf Wizard Topic started 5 years 9 months ago, by Jabbery Last Post 5 years 9 months ago by Jabbery	Replies:7 Views:2004	Last Post by Jabbery 5 years 9 months ago
RPI4 with 7i96 - eSTOP not working on keyboard or axis GUI Category: PnCConf Wizard Topic started 5 years 9 months ago, by Markyd Last Post 5 years 9 months ago by Markyd	Replies:2 Views:1482	Last Post by Markyd 5 years 9 months ago
Servo system not moving correct distance Category: PnCConf Wizard Topic started 5 years 9 months ago, by Michael Last Post 5 years 9 months ago by Michael	Replies:4 Views:1628	Last Post by Michael 5 years 9 months ago
ppnconf - "Create simulated hw conf" missing Category: PnCConf Wizard Topic started 5 years 9 months ago, by Fiury Last Post 5 years 9 months ago by Fiury 1 2	Replies:11 Views:3873	Last Post by Fiury 5 years 9 months ago

Time to create page: 0.058 seconds