SK Commander VFD Parms

Actually I'm doing my lathe so the Lathe .par file would really help.
When you have time it would be great to get that one as well

Which part of PA you in?
I'm in Sunbury just North of Columbus.

I'm still slowly, very slowly working on a DIY Tormach BOB so you could directly connect up.
I have the 1HP SK Commander for my lathe (a G0602) so and want to provide a direct route to using a PP with only a few INI changes, Needed. I may also add individual Home and I would have full control over the ATC port.

Everything is based on the PP config files so far.

I had some good HiRes photos of both the Lathe and MILL Tormach board but it seem when I lost a HD I lost those pics.
If you have any good pics of them that would be great as well if I could impose.

Just to share, I've got most if not all the IO figured out at this point, doing up the Power supply then the processor will be last, well and code for it.

smgvbest wrote: Actually I'm doing my lathe so the Lathe .par file would really help.
When you have time it would be great to get that one as well

Which part of PA you in?
I'm in Sunbury just North of Columbus.

I'm still slowly, very slowly working on a DIY Tormach BOB so you could directly connect up.
I have the 1HP SK Commander for my lathe (a G0602) so and want to provide a direct route to using a PP with only a few INI changes, Needed. I may also add individual Home and I would have full control over the ATC port.

Everything is based on the PP config files so far.

I had some good HiRes photos of both the Lathe and MILL Tormach board but it seem when I lost a HD I lost those pics.
If you have any good pics of them that would be great as well if I could impose.

I'm sorry, I normally view recent and I must have missed this. Sounds like a really neat project! I'm happy to help.

I will try to get you the PAR file by the weekend. I am happy to take pictures. I can do both the lathe, mill, and I have the new board the MX's use as I am getting ready to upgrade my 1100S3 to servos since I got a really good deal on the board and servos. Plus, I'm sick of editing the hal files every time they update to keep my spindle encoder alive.

Shoot me an email, I'll send you the pictures there if you want since the quality will get clipped on here. (Email removed)

I am about 15 minutes north of Harrisburg.

smgvbest wrote: I am in the USA, Ohio

Thats just down the road from Jon Saunders at NYCCNC/Saunders machine works
have you been, do you follow him on youtube
It would be amazing if you went to one of his training sessions and told him you had a Tormach clone.:laugh:
Re your schmatic, ive had good results from JLCPCB for fabricating printed circuit boards
jlcpcb.com/ really cheap and good quality, dont forget "America first" which is exactly what you are doing, making sure you dont pay too much.

snowgoer540 wrote:

smgvbest wrote: Actually I'm doing my lathe so the Lathe .par file would really help.
When you have time it would be great to get that one as well

Which part of PA you in?
I'm in Sunbury just North of Columbus.

I'm still slowly, very slowly working on a DIY Tormach BOB so you could directly connect up.
I have the 1HP SK Commander for my lathe (a G0602) so and want to provide a direct route to using a PP with only a few INI changes, Needed. I may also add individual Home and I would have full control over the ATC port.

Everything is based on the PP config files so far.

I had some good HiRes photos of both the Lathe and MILL Tormach board but it seem when I lost a HD I lost those pics.
If you have any good pics of them that would be great as well if I could impose.

I'm sorry, I normally view recent and I must have missed this. Sounds like a really neat project! I'm happy to help.

I will try to get you the PAR file by the weekend. I am happy to take pictures. I can do both the lathe, mill, and I have the new board the MX's use as I am getting ready to upgrade my 1100S3 to servos since I got a really good deal on the board and servos. Plus, I'm sick of editing the hal files every time they update to keep my spindle encoder alive.

Shoot me an email, I'll send you the pictures there if you want since the quality will get clipped on here.

I am about 15 minutes north of Harrisburg.

Sent you a email just now.
Thank you for the assist

MrJTJinx wrote:

smgvbest wrote: I am in the USA, Ohio

Thats just down the road from Jon Saunders at NYCCNC/Saunders machine works
have you been, do you follow him on youtube
It would be amazing if you went to one of his training sessions and told him you had a Tormach clone.:laugh:
Re your schmatic, ive had good results from JLCPCB for fabricating printed circuit boards
jlcpcb.com/ really cheap and good quality, dont forget "America first" which is exactly what you are doing, making sure you dont pay too much.

I don't watch as much of John as I used too and yes he's about 45-60 minutes or so from me. But then I don't watch as much youtube period as I used to.

I've used JCLPCB, PCBWAY and others, JLCPCB has been my most reliable and quickest delivery so far.
I'm over on EEVBLOG also as SMGVBEST and currently repairing a E4407B Tracking Gen. Though its been on hold for some time

When I am not in a hurry I do use oshpark. good quality but slower to deliver. however jlcpcb does have steaper shipping costs which is a down side.