Configuring a Floating Head

linuxcnc ~/linuxcnc/configs/the_plasma_cutter/the_plasma_cutter.ini

user@debian:~$ linuxcnc ~/linuxcnc/configs/the_plasmac_cutter/the_plasmac_cutter.ini LINUXCNC - 2.8.0-39-g76260b4f7 Machine configuration directory is '/home/user/linuxcnc/configs/the_plasmac_cutter' Machine configuration file is 'the_plasmac_cutter.ini' Starting LinuxCNC... twopass:invoked with <> options twopass:found ./the_plasmac_cutter.hal twopass:found ././plasmac/plasmac.tcl twopass:found ./the_plasmac_cutter_connections.hal Note: Using POSIX realtime hm2: loading Mesa HostMot2 driver version 0.15 hm2_eth: loading Mesa AnyIO HostMot2 ethernet driver version 0.2 iptables: No chain/target/match by that name. hm2_eth: 10.10.10.10: Hardware address: 00:60:1b:16:01:29 hm2_eth: discovered 7I96 hm2/hm2_7i96.0: Smart Serial Firmware Version 43 hm2/hm2_7i96.0: 51 I/O Pins used: hm2/hm2_7i96.0: IO Pin 000 (TB3-01): IOPort hm2/hm2_7i96.0: IO Pin 001 (TB3-02): IOPort hm2/hm2_7i96.0: IO Pin 002 (TB3-03): IOPort hm2/hm2_7i96.0: IO Pin 003 (TB3-04): IOPort hm2/hm2_7i96.0: IO Pin 004 (TB3-05): IOPort hm2/hm2_7i96.0: IO Pin 005 (TB3-06): IOPort hm2/hm2_7i96.0: IO Pin 006 (TB3-07): IOPort hm2/hm2_7i96.0: IO Pin 007 (TB3-08): IOPort hm2/hm2_7i96.0: IO Pin 008 (TB3-09): IOPort hm2/hm2_7i96.0: IO Pin 009 (TB3-10): IOPort hm2/hm2_7i96.0: IO Pin 010 (TB3-11): IOPort hm2/hm2_7i96.0: IO Pin 011 (TB3-13/TB3-14): SSR #0, pin Out-00 (Output) hm2/hm2_7i96.0: IO Pin 012 (TB3-15/TB3-16): SSR #0, pin Out-01 (Output) hm2/hm2_7i96.0: IO Pin 013 (TB3-17/TB3-18): SSR #0, pin Out-02 (Output) hm2/hm2_7i96.0: IO Pin 014 (TB3-19/TB3-20): SSR #0, pin Out-03 (Output) hm2/hm2_7i96.0: IO Pin 015 (TB3-21/TB3-22): SSR #0, pin Out-04 (Output) hm2/hm2_7i96.0: IO Pin 016 (TB3-23/TB3-24): SSR #0, pin Out-05 (Output) hm2/hm2_7i96.0: IO Pin 017 (TB1-02/TB1-03): StepGen #0, pin Step (Output) hm2/hm2_7i96.0: IO Pin 018 (TB1-04/TB1-05): StepGen #0, pin Direction (Output) hm2/hm2_7i96.0: IO Pin 019 (TB1-08/TB1-09): StepGen #1, pin Step (Output) hm2/hm2_7i96.0: IO Pin 020 (TB1-10/TB1-11): StepGen #1, pin Direction (Output) hm2/hm2_7i96.0: IO Pin 021 (TB1-14/TB1-15): StepGen #2, pin Step (Output) hm2/hm2_7i96.0: IO Pin 022 (TB1-16/TB1-17): StepGen #2, pin Direction (Output) hm2/hm2_7i96.0: IO Pin 023 (TB1-20/TB1-21): StepGen #3, pin Step (Output) hm2/hm2_7i96.0: IO Pin 024 (TB1-22-TB1-23): StepGen #3, pin Direction (Output) hm2/hm2_7i96.0: IO Pin 025 (TB2-01/TB2-03): StepGen #4, pin Step (Output) hm2/hm2_7i96.0: IO Pin 026 (TB2-04/TB2-05): StepGen #4, pin Direction (Output) hm2/hm2_7i96.0: IO Pin 027 (TB2-07/TB2-08): Encoder #0, pin A (Input) hm2/hm2_7i96.0: IO Pin 028 (TB2-10/TB2-11): Encoder #0, pin B (Input) hm2/hm2_7i96.0: IO Pin 029 (TB2-13/TB2-14): Encoder #0, pin Index (Input) hm2/hm2_7i96.0: IO Pin 030 (TB2-16/TB2-17): IOPort hm2/hm2_7i96.0: IO Pin 031 (TB2-18/TB2-19): IOPort hm2/hm2_7i96.0: IO Pin 032 (internal): IOPort hm2/hm2_7i96.0: IO Pin 033 (internal): SSR #0, pin AC Ref (internal) (Output) hm2/hm2_7i96.0: IO Pin 034 (P1-01): IOPort hm2/hm2_7i96.0: IO Pin 035 (P1-02): IOPort hm2/hm2_7i96.0: IO Pin 036 (P1-03): IOPort hm2/hm2_7i96.0: IO Pin 037 (P1-04): IOPort hm2/hm2_7i96.0: IO Pin 038 (P1-05): IOPort hm2/hm2_7i96.0: IO Pin 039 (P1-06): IOPort hm2/hm2_7i96.0: IO Pin 040 (P1-07): IOPort hm2/hm2_7i96.0: IO Pin 041 (P1-08): IOPort hm2/hm2_7i96.0: IO Pin 042 (P1-09): IOPort hm2/hm2_7i96.0: IO Pin 043 (P1-11): IOPort hm2/hm2_7i96.0: IO Pin 044 (P1-13): IOPort hm2/hm2_7i96.0: IO Pin 045 (P1-15): IOPort hm2/hm2_7i96.0: IO Pin 046 (P1-17): IOPort hm2/hm2_7i96.0: IO Pin 047 (P1-19): IOPort hm2/hm2_7i96.0: IO Pin 048 (P1-21): IOPort hm2/hm2_7i96.0: IO Pin 049 (P1-23): IOPort hm2/hm2_7i96.0: IO Pin 050 (P1-25): IOPort hm2/hm2_7i96.0: registered twopass: Error in file ./the_plasmac_cutter_connections.hal: Pin 'hm2_7i96.gpio.009.in' does not exist Shutting down and cleaning up LinuxCNC... hm2_eth: HostMot2 ethernet driver unloaded hm2: unloading Note: Using POSIX realtime LinuxCNC terminated with an error. You can find more information in the log: /home/user/linuxcnc_debug.txt and /home/user/linuxcnc_print.txt as well as in the output of the shell command 'dmesg' and in the terminal

cat ~/linuxcnc/configs/the_plasma_cutter/the_plasma_cutter_connections.hal > ~/connections.txt

net plasmac:arc-ok-in hm2_7i96.gpio.009.in => db_arc-ok.in net plasmac:float-switch hm2_7i96.gpio.03.in => db_float.in # net plasmac:breakaway {YOUR BREAKAWAY PIN} => db_breakaway.in # net plasmac:ohmic-probe {YOUR OHMIC PROBE PIN} => db_ohmic.in # net plasmac:ohmic-enable plasmac.ohmic-enable => {YOUR OHMIC ENABLE PIN} net plasmac:torch-on => hm2_7i96.0.ssr.00.out-02 net plasmac:move-up hm2_7i96.gpio.010.in => plasmac.move-up net plasmac:move-down hm2_7i96.gpio.008.in => plasmac.move-down