StepConf Wizard 594 topics

Stepper Configuration Wizard for Parallel Port

Forum Header

Subject	Replies / Views	Last Post
No progress after using stepconfig. Topic started 03 Feb 2010 15:39, by grey1beard Last Post 10 Feb 2010 20:43 by grey1beard 1 2 3 4	Replies:32 Views:28.4k	grey1beard Last Post by grey1beard 10 Feb 2010 20:43
No Step pulses on any step axis Topic started 06 Feb 2010 10:37, by purwanu Last Post 06 Feb 2010 14:37 by purwanu	Replies:2 Views:4536	purwanu Last Post by purwanu 06 Feb 2010 14:37
"Test this axis/Run", and a limit switch Topic started 30 Jan 2010 15:56, by grey1beard Last Post 01 Feb 2010 12:21 by grey1beard	Replies:2 Views:5031	grey1beard Last Post by grey1beard 01 Feb 2010 12:21
Testing XYZ axis, and weird result (of course !) Topic started 27 Jan 2010 17:23, by grey1beard Last Post 31 Jan 2010 11:18 by grey1beard	Replies:3 Views:4161	grey1beard Last Post by grey1beard 31 Jan 2010 11:18
use digital input for machine-power Topic started 12 Jan 2010 21:40, by gironymo Last Post 14 Jan 2010 18:39 by BigJohnT	Replies:3 Views:5703	Last Post by BigJohnT 14 Jan 2010 18:39
reversing motor travel? Topic started 28 Dec 2009 03:23, by jhtitan Last Post 05 Jan 2010 13:15 by jhtitan	Replies:3 Views:4250	jhtitan Last Post by jhtitan 05 Jan 2010 13:15
z axis scale problems. Topic started 03 Jan 2010 18:38, by pcarson Last Post 03 Jan 2010 20:32 by BigJohnT	Replies:3 Views:5750	Last Post by BigJohnT 03 Jan 2010 20:32
Jog speed in "test axis" dialog Topic started 31 Dec 2009 14:37, by step4linux Last Post 31 Dec 2009 14:37 by step4linux	Replies:0 Views:4029	step4linux Last Post by step4linux 31 Dec 2009 14:37
Home Topic started 23 Dec 2009 20:53, by dekell71 Last Post 24 Dec 2009 00:03 by cmorley	Replies:2 Views:3890	cmorley Last Post by cmorley 24 Dec 2009 00:03
Where is Stepper Config Wizard Topic started 17 Dec 2009 18:01, by Ian@eagland.co.uk Last Post 18 Dec 2009 09:38 by Ian@eagland.co.uk	Replies:2 Views:4806	Ian@eagland.co.uk Last Post by Ian@eagland.co.uk 18 Dec 2009 09:38
TA8435H 5axis driver config of duel X axis stepper Topic started 13 Dec 2009 23:17, by 2e0poz Last Post 14 Dec 2009 10:12 by 2e0poz	Replies:1 Views:6369	2e0poz Last Post by 2e0poz 14 Dec 2009 10:12
step configure wizard Topic started 20 Nov 2009 19:47, by ZARF Last Post 01 Dec 2009 02:03 by cmorley	Replies:4 Views:4544	cmorley Last Post by cmorley 01 Dec 2009 02:03
3-Axis Millling - Motors go wrong way.... help.... Topic started 26 Oct 2009 09:04, by deltagirl Last Post 25 Nov 2009 23:49 by deltagirl	Replies:4 Views:5466	Last Post by deltagirl 25 Nov 2009 23:49
Homing Switch ignored Topic started 23 Nov 2009 20:16, by cpohl Last Post 24 Nov 2009 12:02 by BigJohnT	Replies:3 Views:3994	Last Post by BigJohnT 24 Nov 2009 12:02
Homing with tandem X axis Topic started 17 Nov 2009 04:06, by bpwood Last Post 18 Nov 2009 12:51 by bpwood	Replies:4 Views:6585	bpwood Last Post by bpwood 18 Nov 2009 12:51
help error on install emc2-2.3.0 Topic started 15 Oct 2009 02:46, by peixin Last Post 27 Oct 2009 12:47 by deltagirl	Replies:2 Views:5854	Last Post by deltagirl 27 Oct 2009 12:47
Spindle Speed box removal Topic started 27 Sep 2009 00:55, by cwebs Last Post 26 Oct 2009 23:07 by cwebs	Replies:3 Views:5974	cwebs Last Post by cwebs 26 Oct 2009 23:07
Configuring EMC on a belt-driven router Topic started 14 Oct 2009 19:32, by scoop113 Last Post 16 Oct 2009 12:06 by BigJohnT	Replies:1 Views:5857	Last Post by BigJohnT 16 Oct 2009 12:06
Fault M3, OK M3 S20000? Topic started 13 Oct 2009 18:00, by radioelf Last Post 13 Oct 2009 18:00 by radioelf	Replies:0 Views:4112	radioelf Last Post by radioelf 13 Oct 2009 18:00
Help with new EMC2 config and 3 axis router. Topic started 08 Sep 2009 00:39, by NeilR Last Post 10 Oct 2009 10:07 by NeilR 1 2	Replies:18 Views:23.5k	NeilR Last Post by NeilR 10 Oct 2009 10:07

Time to create page: 0.119 seconds