StepConf Wizard 592 topics

Stepper Configuration Wizard for Parallel Port

Forum Header

Subject	Replies / Views	Last Post
Chinese TS 3040 LL Set Topic started 03 Oct 2016 21:11, by Soltan Last Post 19 Feb 2017 00:59 by grump	Replies:9 Views:5846	Last Post by grump 19 Feb 2017 00:59
Odd Pitch Results Topic started 08 Feb 2017 03:11, by CFLBob Last Post 08 Feb 2017 21:50 by CFLBob 1 2	Replies:11 Views:3427	CFLBob Last Post by CFLBob 08 Feb 2017 21:50
How are the DRO and Stepgen kept in sync? Topic started 29 Dec 2016 22:06, by GaryLa Last Post 10 Jan 2017 21:42 by PCW 1 2	Replies:11 Views:4757	Last Post by PCW 10 Jan 2017 21:42
Taig mill with Gecko540 driver Topic started 19 Dec 2016 18:21, by freedomlives Last Post 19 Dec 2016 19:14 by freedomlives	Replies:2 Views:1481	Last Post by freedomlives 19 Dec 2016 19:14
How to find the driver timing? Topic started 27 Nov 2016 06:35, by emad Last Post 27 Nov 2016 11:03 by tommylight	Replies:3 Views:1845	Last Post by tommylight 27 Nov 2016 11:03
Backlasah compensation Topic started 18 Nov 2016 12:37, by ArtJ Last Post 18 Nov 2016 13:13 by andypugh	Replies:1 Views:1595	Last Post by andypugh 18 Nov 2016 13:13
need help with pitch calibration Topic started 04 May 2016 02:37, by Bradmillikan Last Post 11 Nov 2016 19:56 by SenorAguas	Replies:8 Views:3081	SenorAguas Last Post by SenorAguas 11 Nov 2016 19:56
Measure Table Movement Directly for Thread Pitch Topic started 17 Jun 2016 00:36, by chevydan6 Last Post 11 Nov 2016 19:51 by SenorAguas	Replies:2 Views:1837	SenorAguas Last Post by SenorAguas 11 Nov 2016 19:51
Max Velocity gets set at Ludicrous Speed Topic started 20 Jun 2016 04:08, by thaelin Last Post 11 Nov 2016 19:45 by SenorAguas	Replies:2 Views:2312	SenorAguas Last Post by SenorAguas 11 Nov 2016 19:45
[Bug Report] Crash using Mach3 imported configuration Topic started 10 Nov 2016 01:40, by marcorighi Last Post 10 Nov 2016 08:37 by andypugh	Replies:1 Views:1329	Last Post by andypugh 10 Nov 2016 08:37
Need help Topic started 23 Oct 2016 13:14, by crosscalls Last Post 07 Nov 2016 11:10 by eFalegname	Replies:2 Views:1480	Last Post by eFalegname 07 Nov 2016 11:10
Z Axis Both Limit & Home switch is ignored - X & Y fine Topic started 04 Nov 2016 20:27, by LukeH Last Post 05 Nov 2016 21:30 by andypugh	Replies:3 Views:1669	Last Post by andypugh 05 Nov 2016 21:30
Parallel port not working Topic started 01 Nov 2016 19:07, by ax650 Last Post 01 Nov 2016 21:47 by andypugh	Replies:9 Views:2151	Last Post by andypugh 01 Nov 2016 21:47
Taig cnc mini mill Gecko 540 setup help Topic started 01 Nov 2016 17:52, by ArtJ Last Post 01 Nov 2016 18:57 by Todd Zuercher	Replies:1 Views:1678	Last Post by Todd Zuercher 01 Nov 2016 18:57
world's dumbest setup question Topic started 24 Oct 2016 22:32, by milu Last Post 25 Oct 2016 20:35 by milu	Replies:3 Views:1543	milu Last Post by milu 25 Oct 2016 20:35
Mach3 conf import fails Topic started 20 Oct 2016 10:06, by Nibbler Last Post 21 Oct 2016 16:11 by Todd Zuercher	Replies:5 Views:1879	Last Post by Todd Zuercher 21 Oct 2016 16:11
E-Stop Enabled but Does Not Respond Topic started 18 Oct 2016 15:48, by miketim Last Post 19 Oct 2016 12:29 by Todd Zuercher	Replies:9 Views:1725	Last Post by Todd Zuercher 19 Oct 2016 12:29
Stepconf Wiz?..how much does it actually convert Topic started 30 Aug 2016 11:13, by Spectre Last Post 30 Aug 2016 22:04 by PCW	Replies:3 Views:1689	Last Post by PCW 30 Aug 2016 22:04
Motors run at 1/5th travel Topic started 26 Aug 2016 09:10, by bobhare Last Post 27 Aug 2016 15:34 by bobhare	Replies:2 Views:1712	bobhare Last Post by bobhare 27 Aug 2016 15:34
The Express pci parport card address .What? Topic started 20 Aug 2016 14:39, by 819132306 Last Post 22 Aug 2016 15:57 by 819132306 1 2 3	Replies:22 Views:5774	819132306 Last Post by 819132306 22 Aug 2016 15:57

Time to create page: 0.148 seconds