StepConf Wizard 592 topics

Stepper Configuration Wizard for Parallel Port

Forum Header

Subject	Replies / Views	Last Post
Help: configure a Servo motor with (PUL/DIR) as a Spindle by Par-port stepconfig Topic started 18 Nov 2024 15:37, by sk_linuxcnc Last Post 22 Nov 2024 17:57 by PCW 1 2	Replies:13 Views:370	Last Post by PCW 22 Nov 2024 17:57
Latency Test is weak... Topic started 13 Mar 2024 17:16, by Topi69 Last Post 20 Nov 2024 16:56 by langdons 1 2	Replies:13 Views:1527	langdons Last Post by langdons 20 Nov 2024 16:56
Z axis goes in the wrong direction, so after home-all Topic started 03 Nov 2024 18:12, by lgrfbs Last Post 09 Nov 2024 23:40 by lgrfbs	Replies:5 Views:316	Last Post by lgrfbs 09 Nov 2024 23:40
Spindle setup Topic started 09 Jan 2024 20:33, by frprim Last Post 13 Oct 2024 12:48 by BSOD 1 2	Replies:12 Views:3018	BSOD Last Post by BSOD 13 Oct 2024 12:48
Motor locks but will not move when testing Topic started 26 Jul 2024 20:45, by waukeenahBob Last Post 07 Oct 2024 22:19 by rudi 1 2	Replies:15 Views:1885	rudi Last Post by rudi 07 Oct 2024 22:19
Help with Mesa 7I97T card CCW and CW Topic started 06 Oct 2024 23:50, by akim14 Last Post 07 Oct 2024 00:06 by PCW	Replies:1 Views:155	Last Post by PCW 07 Oct 2024 00:06
Taig Lathe conversion to LinuxCNC: M3 is not turning on spindle Topic started 26 Jul 2024 13:33, by Cerezas Last Post 27 Jul 2024 13:53 by Aciera	Replies:4 Views:353	Last Post by Aciera 27 Jul 2024 13:53
Stepconfig wont set up tandem y axis limit and home? Topic started 08 Jul 2024 01:32, by redeye_joe Last Post 15 Jul 2024 08:26 by rodw	Replies:2 Views:379	Last Post by rodw 15 Jul 2024 08:26
How to setup simultaneous tandem Y and tandem Z Topic started 27 Mar 2024 22:28, by Antonio Gross Last Post 27 May 2024 05:11 by jimmyrig	Replies:4 Views:1080	jimmyrig Last Post by jimmyrig 27 May 2024 05:11
'Test this axis' Topic started 20 Apr 2024 03:38, by JohnBr00ker Last Post 04 May 2024 00:39 by JohnBr00ker 1 2	Replies:10 Views:1610	Last Post by JohnBr00ker 04 May 2024 00:39
Z-Axis no Ref configurable Topic started 25 Apr 2024 10:45, by Satai Last Post 27 Apr 2024 21:42 by tommylight 1 2	Replies:12 Views:1176	Last Post by tommylight 27 Apr 2024 21:42
Leadscrew pitch calibration Topic started 22 Apr 2024 23:25, by Dave2024 Last Post 23 Apr 2024 00:46 by Dave2024	Replies:2 Views:445	Last Post by Dave2024 23 Apr 2024 00:46
Help with drive belt setup Topic started 15 Apr 2024 21:04, by MDP Last Post 16 Apr 2024 22:28 by tommylight	Replies:5 Views:536	Last Post by tommylight 16 Apr 2024 22:28
Migrating to another PC Topic started 16 Mar 2024 08:07, by cncjerry Last Post 16 Mar 2024 20:30 by cncjerry	Replies:7 Views:660	cncjerry Last Post by cncjerry 16 Mar 2024 20:30
AXIS doesn't work Topic started 10 Aug 2023 20:32, by Crenos Last Post 16 Mar 2024 08:13 by cncjerry	Replies:7 Views:1247	cncjerry Last Post by cncjerry 16 Mar 2024 08:13
Type of joint ANGLE Topic started 14 Mar 2024 23:05, by noqui Last Post 16 Mar 2024 00:43 by tommylight	Replies:1 Views:416	Last Post by tommylight 16 Mar 2024 00:43
CW8060 swapping label Topic started 13 Mar 2024 09:09, by Topi69 Last Post 13 Mar 2024 09:09 by Topi69	Replies:0 Views:469	Topi69 Last Post by Topi69 13 Mar 2024 09:09
Stepper Motor Configuration problem Topic started 12 Mar 2024 14:20, by noqui Last Post 12 Mar 2024 15:58 by noqui	Replies:5 Views:576	noqui Last Post by noqui 12 Mar 2024 15:58
CW8060 stepper driver timing settings Topic started 12 Mar 2024 09:59, by Topi69 Last Post 12 Mar 2024 13:50 by tommylight	Replies:1 Views:467	Last Post by tommylight 12 Mar 2024 13:50
Importing imperial toolset into CNC Topic started 27 Feb 2024 21:40, by Basemetal Last Post 02 Mar 2024 21:03 by rodw	Replies:2 Views:597	Last Post by rodw 02 Mar 2024 21:03

Time to create page: 0.137 seconds