StepConf Wizard 322 topics

Stepper Configuration Wizard for Parallel Port

Forum Header

Subject	Replies / Views	Last Post
help with axis configuration Topic started 30 Jan 2016 23:26, by sandman92k Last Post 01 Feb 2016 20:14 by cmorley 1 2	Replies:14 Views:4751	cmorley Last Post by cmorley 01 Feb 2016 20:14
Thanks to everyone for the help Topic started 01 Feb 2016 18:13, by sandman92k Last Post 01 Feb 2016 20:02 by cmorley	Replies:1 Views:1575	cmorley Last Post by cmorley 01 Feb 2016 20:02
sim_hardware inverted input pins do not exist? Topic started 23 Jan 2016 20:31, by summetj Last Post 24 Jan 2016 04:43 by cmorley	Replies:1 Views:1999	cmorley Last Post by cmorley 24 Jan 2016 04:43
Stepconf HAL: ERROR: duplicate component name 'hal Topic started 09 Jan 2016 17:41, by nicokid Last Post 15 Jan 2016 01:50 by cmorley 1 2	Replies:16 Views:7044	cmorley Last Post by cmorley 15 Jan 2016 01:50
Reversing X Axis? Topic started 14 Jan 2016 03:14, by spinnaker Last Post 14 Jan 2016 16:27 by andypugh	Replies:3 Views:3034	Last Post by andypugh 14 Jan 2016 16:27
Help please !!! Servo configuration with stepconf. Topic started 30 Apr 2012 11:18, by ishman Last Post 13 Jan 2016 16:05 by jepler 1 2 3 ... 6	Replies:57 Views:48.2k	Last Post by jepler 13 Jan 2016 16:05
Calibration Problem With A Axis >HELP Please< Topic started 06 Dec 2015 13:13, by Sergio Last Post 13 Jan 2016 15:30 by Sergio 1 2	Replies:12 Views:5003	Sergio Last Post by Sergio 13 Jan 2016 15:30
LinuxCNC V2.7 and Sherline Mill - SOLVED Topic started 03 Jan 2016 00:06, by HDVideo Last Post 05 Jan 2016 17:55 by HDVideo	Replies:3 Views:2979	HDVideo Last Post by HDVideo 05 Jan 2016 17:55
Configuring e-stop disables motors Topic started 31 Dec 2015 18:13, by ex262 Last Post 02 Jan 2016 11:06 by ArcEye	Replies:4 Views:4903	ArcEye Last Post by ArcEye 02 Jan 2016 11:06
China board for PWM Commutation??? Topic started 19 Dec 2015 16:08, by cyrut2 Last Post 21 Dec 2015 12:27 by andypugh	Replies:1 Views:1946	Last Post by andypugh 21 Dec 2015 12:27
Red China Board Topic started 18 Dec 2015 22:40, by cyrut2 Last Post 19 Dec 2015 19:52 by Todd Zuercher	Replies:6 Views:2365	Last Post by Todd Zuercher 19 Dec 2015 19:52
Lathe step config question Topic started 09 Dec 2015 15:58, by Davenc Last Post 09 Dec 2015 16:53 by Davenc	Replies:2 Views:1683	Davenc Last Post by Davenc 09 Dec 2015 16:53
How to set a bit in the paralell port Topic started 08 Dec 2015 17:50, by Fredrik2556 Last Post 08 Dec 2015 20:02 by Todd Zuercher	Replies:1 Views:1851	Last Post by Todd Zuercher 08 Dec 2015 20:02
Version 2.7.3. Topic started 07 Dec 2015 22:27, by Engineer Dwayne Last Post 08 Dec 2015 00:30 by cmorley	Replies:1 Views:1706	cmorley Last Post by cmorley 08 Dec 2015 00:30
Version 2.7.3 - paraport support Topic started 07 Dec 2015 22:24, by Engineer Dwayne Last Post 08 Dec 2015 00:07 by tommylight	Replies:1 Views:1585	Last Post by tommylight 08 Dec 2015 00:07
Error during setup Z to run Blacktooth laser Topic started 27 Oct 2015 09:18, by ubergeek Last Post 07 Dec 2015 13:25 by andypugh 1 2	Replies:16 Views:5602	Last Post by andypugh 07 Dec 2015 13:25
How to see parameters previously used in a config. Topic started 02 Dec 2015 17:00, by hickbooz Last Post 05 Dec 2015 12:56 by hickbooz	Replies:4 Views:1660	hickbooz Last Post by hickbooz 05 Dec 2015 12:56
setting up cnc xpro v2 control board Topic started 04 Nov 2015 22:39, by pauric Last Post 04 Nov 2015 23:08 by ArcEye	Replies:4 Views:9683	ArcEye Last Post by ArcEye 04 Nov 2015 23:08
Worm drive Topic started 30 Oct 2015 06:08, by bill516 Last Post 31 Oct 2015 03:10 by bill516	Replies:4 Views:2349	bill516 Last Post by bill516 31 Oct 2015 03:10
Z Stepper won't run Topic started 21 Oct 2015 04:09, by bwg Last Post 26 Oct 2015 23:07 by cncbasher 1 2	Replies:15 Views:5224	cncbasher Last Post by cncbasher 26 Oct 2015 23:07

Time to create page: 0.129 seconds