1. Forum
  3. Search

Advanced Search

Search Results (Searched for: )

  • Edi_48
  • Edi_48
16 Jun 2025 08:44
Replied by Edi_48 on topic Rote LED

Rote LED

Category: Deutsch

Netzteil 5 volt 10 Amper
  • Edi_48
  • Edi_48
16 Jun 2025 08:35
Replied by Edi_48 on topic Rote LED

Rote LED

Category: Deutsch

60000 packets transmitted, 59992 received, +8 errors, 0.0133333% packet loss, time 60099ms
rtt min/avg/max/mdev = 0.048/0.133/6.074/0.075 ms, pipe 9

Beim starten von Linuxcnc und Steuerung sind alle 4LED grün nach dem Test brennen nur 2 LDS
  • mc_cubus
  • mc_cubus
16 Jun 2025 08:16 - 16 Jun 2025 08:22
Replied by mc_cubus on topic Probe tripped during non-probe move

Probe tripped during non-probe move

Category: Basic Configuration

Hey, thank you for your insights. They can definitely be helpful. I solved the problem bit differently and if someone will ever need that I will just post it here:

I did set the digital output pin and connected it together with the actual probing trigger using AND component. So basically in .hal it looks like that:
[code]net probe-enable motion.digital.out-00 => and2.0.in0 # Sets and2.0.in0 based on M64 / M65
net near-window near.0.out => and2.0.in1 # Sets and2.0.in1 if sensor is in probing window range: near.0.out
net gated-probe and2.0.out => motion.probe-input




[code][code][code][code]M64 P0              # sets digital output pin P0 to TRUE: enable probing
G38.3 Z-180 F150    # Do the probing movement
M65 P0              # sets digital output pin P0 to FALSE: disable probing


[code][code]Maybe it's not the cleanest solution, but at least it works :)
[/code][/code][/code][/code][/code][/code][/code]
  • DMNZ
  • DMNZ
16 Jun 2025 07:28
Replied by DMNZ on topic Error finishing read... *sigh*

Error finishing read... *sigh*

Category: Computers and Hardware

cheap Pentium J2900. i just posted my test results with settings few days ago in a thread called Pentium J2900 fanless pc test results, you can compare it with yours.
  • meister
  • meister
16 Jun 2025 05:32
Replied by meister on topic LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)

LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)

Category: Computers and Hardware

I'm afraid there is still a bug when generating the ini/hal.

scale in need to be set in the encoder config (signals -> scale):


and out in the joint pwm/dir config (joint -> General -> Scale):
  • SebastianM
  • SebastianM
16 Jun 2025 03:38
Replied by SebastianM on topic Email Notification?

Email Notification?

Category: Forum Questions

I do get emails if I request a new password, but I never get any notifications for new replies.
  • SebastianM
  • SebastianM
16 Jun 2025 03:36 - 16 Jun 2025 03:45
Replied by SebastianM on topic Error finishing read... *sigh*

Error finishing read... *sigh*

Category: Computers and Hardware

Will post a latency histogram on Thursday after a business trip.

Which hardware/ pc are you using?
  • cmorley
  • cmorley
16 Jun 2025 03:34 - 16 Jun 2025 03:35
Replied by cmorley on topic GUI that somewhat resembles haas or fanuc workflow.

GUI that somewhat resembles haas or fanuc workflow.

Category: General LinuxCNC Questions

 

  • snowgoer540
  • snowgoer540's Avatar
16 Jun 2025 01:40
Replied by snowgoer540 on topic Email Notification?

Email Notification?

Category: Forum Questions

Ok. Guess if they work for you they work for everyone.

Problem solved ¯\_(ツ)_/¯
  • tommylight
  • tommylight's Avatar
16 Jun 2025 00:46
Replied by tommylight on topic Email Notification?

Email Notification?

Category: Forum Questions

Oh i am sure:
  • directandrew
  • directandrew
16 Jun 2025 00:34
Replied by directandrew on topic New to linuxcnc, basic question for DRO modes with encoded handwheels

New to linuxcnc, basic question for DRO modes with encoded handwheels

Category: General LinuxCNC Questions

Based on what im reading, it does seem ill need a larger card to handle all the limit switches and 3 encoders, one for each hand-wheel. I will prob go RJ45 as the parallel ports are less and less these days.

Thinking this guy, not cheap but one stop shop correct?
store.mesanet.com/index.php?route=produc...id=399&search=7I76EU
  • spumco
  • spumco
16 Jun 2025 00:27
Replied by spumco on topic GUI that somewhat resembles haas or fanuc workflow.

GUI that somewhat resembles haas or fanuc workflow.

Category: General LinuxCNC Questions

Is the Fanuc style of Gcodes display really better then linuxcnc's?

 

Not in my opinion.

There are quite a few characteristics with Fanuc (and other commercial offerings) which are user-unfriendly compared to LCNC.  The gcode display is a good example of that.

Another one I hate is when my Fanuc 21TB removes the tool offset when I switch from MDI to jogging and then to some other mode.
  • snowgoer540
  • snowgoer540's Avatar
16 Jun 2025 00:01
Replied by snowgoer540 on topic Email Notification?

Email Notification?

Category: Forum Questions

I wouldn't be so sure.  I haven't received the moderator emails (email for every single post) since March, and it was sporadic before that.  I haven't received an email for a thread I asked to be notified of replies for in ... years.  

At this point it's not a complaint, I've just accepted it, getting an email for every post is excessive anyways.  
  • DMNZ
  • DMNZ
15 Jun 2025 23:47
Replied by DMNZ on topic Error finishing read... *sigh*

Error finishing read... *sigh*

Category: Computers and Hardware

yip, very similar to what i am having on mine, interesting to see your latency histogram figures.

i still see occasional 1+ms packets once in a while mostly when I heavily use disk or usb which interrupt pci bus, or may be it is just noise and bad cable, but as i mentioned hm2_eth can work around it unless you get something over 3-4ms or 3-4 long packets in a row. then it will error out with can't finish read.

cheers!
Displaying 14026 - 14040 out of 16960 results.
  1. Forum
  3. Search
Time to create page: 0.451 seconds
Powered by Kunena Forum