Plasmac 525 topics

A place to ask questions about the Plasmac interface

Subject	Replies / Views	Last Post
QtPlasmac Updates Topic started 19 Jan 2022 03:37, by phillc54 Locked Last Post 24 Jan 2023 21:09 by snowgoer540 Locked	Replies:2 Views:25.7k	Last Post by snowgoer540 24 Jan 2023 21:09
Photos Topic started 23 Apr 2020 01:46, by phillc54 Last Post 01 Jan 2023 02:54 by caretech 1 2 3 ... 15	Replies:146 Views:27.5k	Last Post by caretech 01 Jan 2023 02:54
QtPlasmaC release. Topic started 15 Mar 2021 09:00, by phillc54 Last Post 17 Aug 2022 23:58 by phillc54 1 2 3 ... 21	Replies:203 Views:27.5k	Last Post by phillc54 17 Aug 2022 23:58
Plasmac Post Processors Topic started 23 Feb 2020 02:44, by phillc54 Last Post 29 Apr 2022 23:29 by phillc54 1 2	Replies:18 Views:18.1k	Last Post by phillc54 29 Apr 2022 23:29
Post Processor for LinuxCNC and PlasmaC Topic started 13 May 2019 07:13, by JTknives Last Post 25 Nov 2021 01:10 by tommylight 1 2 3 ... 13	Replies:122 Views:28.3k	Last Post by tommylight 25 Nov 2021 01:10
IMPORTANT NOTICE for PlasmaC users Topic started 12 May 2021 00:38, by phillc54 Last Post 25 Aug 2021 04:33 by phillc54	Replies:1 Views:3151	Last Post by phillc54 25 Aug 2021 04:33
Hypertherm Powermax65 Toolset Topic started 26 Jul 2020 17:42, by CBEAR Last Post 22 Feb 2021 02:45 by phillc54 1 2	Replies:12 Views:11.1k	Last Post by phillc54 22 Feb 2021 02:45
PlasmaC Documentation Topic started 25 Aug 2019 06:07, by phillc54 Locked Last Post 25 Aug 2019 06:07 by phillc54 Locked	Replies:0 Views:9634	Last Post by phillc54 25 Aug 2019 06:07

Fusion 360 post processing with the post processor from the sticky thread Topic started 18 Jan 2023 09:47, by Deveraux Last Post 04 Feb 2023 12:18 by andypugh	Replies:1 Views:121	Last Post by andypugh 04 Feb 2023 12:18
Error with T0 M6 (select plasma tool) Topic started 01 Feb 2023 21:33, by edgemir Last Post 03 Feb 2023 17:36 by edgemir	Replies:8 Views:244	edgemir Last Post by edgemir 03 Feb 2023 17:36
Camera setup Topic started 20 Jan 2023 11:10, by Howlingg Last Post 28 Jan 2023 23:22 by phillc54 1 2	Replies:12 Views:662	Last Post by phillc54 28 Jan 2023 23:22
Probing/Ohmic faults. Topic started 24 Jan 2023 12:08, by rodw Last Post 28 Jan 2023 11:26 by phillc54 1 2	Replies:13 Views:511	Last Post by phillc54 28 Jan 2023 11:26
Fusion 360 post processor file for Plamac Topic started 15 Jan 2020 01:27, by CFE Last Post 20 Jan 2023 22:04 by Doug @ Design8Studio.com 1 2 3 ... 5	Replies:44 Views:5142	Last Post by Doug @ Design8Studio.com 20 Jan 2023 22:04
jogging disabled if float switch triggered Topic started 19 Jan 2023 08:28, by rodw Last Post 19 Jan 2023 09:10 by snowgoer540	Replies:5 Views:128	Last Post by snowgoer540 19 Jan 2023 09:10
Enable Auto hole cutting Topic started 18 Jan 2023 23:52, by RobKin Last Post 18 Jan 2023 23:57 by phillc54	Replies:1 Views:109	Last Post by phillc54 18 Jan 2023 23:57
qtplasmac_gcode.py: not found after upgrade Topic started 15 Jan 2023 15:12, by Howlingg Last Post 18 Jan 2023 09:27 by Howlingg	Replies:9 Views:269	Howlingg Last Post by Howlingg 18 Jan 2023 09:27
THCAD-5 Reading negative Voltages Topic started 10 Jan 2023 21:02, by Deveraux Last Post 17 Jan 2023 08:39 by Deveraux	Replies:6 Views:218	Deveraux Last Post by Deveraux 17 Jan 2023 08:39
Mesa THCAD-10 Topic started 03 Jan 2023 12:42, by aabtech Last Post 12 Jan 2023 15:53 by mariusl	Replies:4 Views:202	Last Post by mariusl 12 Jan 2023 15:53
Gap cut Topic started 05 Dec 2022 17:37, by paulsao Last Post 05 Jan 2023 23:17 by paulsao	Replies:2 Views:325	Last Post by paulsao 05 Jan 2023 23:17
Penetration Issue Topic started 28 Dec 2022 17:45, by Sushi Last Post 03 Jan 2023 14:18 by tommylight	Replies:2 Views:199	Last Post by tommylight 03 Jan 2023 14:18

Time to create page: 0.403 seconds