Remora - ethernet NVEM / EC300 / EC500 cnc board

beauxnez wrote:

has anyone made qtplasmac work with a NVEM card?

Code:

  File "/usr/share/qtvcp/screens/qtplasmac/qtplasmac_handler.py", line 220, in __init__     float(self.iniFile.find('AXIS_Z', 'OFFSET_AV_RATIO')) * 60   File "/usr/share/qtvcp/screens/qtplasmac/qtplasmac_handler.py", line 220, in __init__     float(self.iniFile.find('AXIS_Z', 'OFFSET_AV_RATIO')) * 60

If anyone had a qtplasmac config for the NVEM, they would have ended our suffering 2 pages ago.
its probably this, i think the THC probably uses external offsets.
add this line and report back
github.com/rodw-au/showstopper/blob/master/my_Plasma.ini#L226

or the next time an error pops up, you can try and trace it out, using all those other plasmac examples I posted before, or by referring to rods config I just listed, otherwise this will be a very long process.

well I'm saved because I see that you are starting to lose patience,
 but I'm not fired because I have the emergency stop that does not unlock but I think I know where it comes from,
 for info I went to debian 12 with linuxcnc 2.9.4 while I was on mint with linuxcnc 2.9.0

 


Many thanks to you I will post my file and the 2 to 3 things that I know

forum.linuxcnc.org/plasmac/43127-qtplasm...-user-request-enable
forum.linuxcnc.org/plasmac/54940-qtplasmac-estop-stuck
www.forum.linuxcnc.org/38-general-linuxc...plasmac-wont-turn-on

lol its fine, but its going to take a while to get it working 1 error at a time.

Good evening, I tried to follow this tutorial, but I couldn't find the stlink bin file, the DAPLink file no longer exists, I couldn't find it anywhere

This is no longer the recommended method to flash the board. pyOCD has proven to be more reliable.

Use the first part of the video to convert a ST-Link to a CMSIS-DAP probe with the following firmware.

github.com/scottalford75/Remora-NVEM/blo...NVEM-STM32-1.0.0.bin

And then use pyOCD to flash the board as described in this thread.

Should I just download the bim from pyodc and put it in stlink v2 and after that I will be able to record remora on nven? Could you detail me step by step?

hi no you use a stlink (the green one on the video) to flash a second stlink adapter (the blue one on the video), 
then you take the key that you flashed (the blue one) you connect it to a pc and you use PYOCD with the command pyocd flash .\remora-rt1052-3.1.3.bin --target mimxrt1050_quadspi as in the photo


youtube.com/shorts/kLOyWslSZU0?si=C3GMQaH--oAvvTZk

 

hi Scotta
I wanted to compliment you on the work you have done and made available
to the LinuxCNC community.
I am excited about it and I bought an NVEM V5 to try to install the Remora firmware,
but when I opened the case I noticed that the chip is not an STM32F207 but the one in the photo


 


is it still compatible or did I buy the wrong card?

Thanks if you can give me some advice

P.S. sorry Scotta
I went a bit back with the posts and at 191 there is the answer to my question, thanks,
I'll move on....

Thank you so much for your help, your video helped a lot, I was able to flash on Stlink V2, but how do I install and use pyqcd, I didn't find anything that helped me, I could explain to me, or point someone who has already asked this question to see what He did1